Shaft Length 9.5mm

Shaft length: 14mm

Mounting hole 13mm Dia.

Mounting hole 13mm Dia.

Skt 2.5mm Chassis mount

Skt 2.1mm Chassis mount

Skt 2.5mm Chassis mount. Mounting Hole 8Ø

Skt 2.1mm Chassis mount. Mounting Hole 8Ø

Socket 2.5mm PCB

Skt 2.1mm PCB

Shaft length: 9.5mm

Shaft length: 9.5mm

As used in prototyping, design & chip programming. Suits standard 2.54mm pin pitch IC’s. P 0594 is a universal type allowing both narrow and wide pitch 28 pin IC’s. PCB pin size 0.8mm.

IC Row Spacing:

15.24mm

As used in prototyping, design & chip programming. Suits standard 2.54mm pin pitch IC’s. P 0594 is a universal type allowing both narrow and wide pitch 28 pin IC’s. PCB pin size 0.8mm.

IC Row Spacing:

7.62-15.24mm

As used in prototyping, design & chip programming. Suits standard 2.54mm pin pitch IC’s. PCB pin size 0.8mm.

IC Row Spacing:

7.62mm

As used in prototyping, design & chip programming. Suits standard 2.54mm pin pitch IC’s. P 0594 is a universal type allowing both narrow and wide pitch 28 pin IC’s. PCB pin size 0.8mm.

IC Row Spacing:

7.62mm

** Minimum purchase of 12 units **

Specifications:

Contact Resistance: 30M Ohms Max @ DC 100mA Insulation Resistance: 1000M Ohms Min @ DC 250V Current Rating: 1 Amp Dielectric Voltage: AC 500V for 1 Minute Operating Temp: -55° to 105° C Gold Plated Beryllium Copper Contacts

Dimensions:

A: 50.8 B:48.26 C: 17.78 D: 15.24

** Minimum purchase of 17 units **

Specifications:

Contact Resistance: 30M Ohms Max @ DC 100mA Insulation Resistance: 1000M Ohms Min @ DC 250V Current Rating: 1 Amp Dielectric Voltage: AC 500V for 1 Minute Operating Temp: -55° to 105° C Gold Plated Beryllium Copper Contacts

Dimensions:

A: 35.56 B:33.02 C: 17.78 D: 15.24

** Minimum purchase of 20 units **

Specifications:

Contact Resistance: 30M Ohms Max @ DC 100mA Insulation Resistance: 1000M Ohms Min @ DC 250V Current Rating: 1 Amp Dielectric Voltage: AC 500V for 1 Minute Operating Temp: -55° to 105° C Gold Plated Beryllium Copper Contacts

Dimensions:

A: 30.48 B:27.94 C: 17.78 D: 15.24

** Minimum purchase of 17 units **

Specifications:

Contact Resistance: 30M Ohms Max @ DC 100mA Insulation Resistance: 1000M Ohms Min @ DC 250V Current Rating: 1 Amp Dielectric Voltage: AC 500V for 1 Minute Operating Temp: -55° to 105° C Gold Plated Beryllium Copper Contacts

Dimensions:

A: 35.56 B: 33.02 C: 10.16 D: 7.62

** Minimum purchase of 20 units **

Specifications:

Contact Resistance: 30M Ohms Max @ DC 100mA Insulation Resistance: 1000M Ohms Min @ DC 250V Current Rating: 1 Amp Dielectric Voltage: AC 500V for 1 Minute Operating Temp: -55° to 105° C Gold Plated Beryllium Copper Contacts

Dimensions:

A: 30.48 B: 27.94 C: 10.16 D: 7.62

** Minimum purchase of 24 units **

Specifications:

Contact Resistance: 30M Ohms Max @ DC 100mA Insulation Resistance: 1000M Ohms Min @ DC 250V Current Rating: 1 Amp Dielectric Voltage: AC 500V for 1 Minute Operating Temp: -55° to 105° C Gold Plated Beryllium Copper Contacts

Dimensions:

A: 25.4 B:22.86 C: 10.16 D: 7.62

** Minimum purchase of 26 units **

Specifications:

Contact Resistance: 30M Ohms Max @ DC 100mA Insulation Resistance: 1000M Ohms Min @ DC 250V Current Rating: 1 Amp Dielectric Voltage: AC 500V for 1 Minute Operating Temp: -55° to 105° C Gold Plated Beryllium Copper Contacts

Dimensions:

A: 22.86 B:20.32 C: 10.16 D: 7.62

** Minimum purchase of 30 units **

Specifications:

Contact Resistance: 30M Ohms Max @ DC 100mA Insulation Resistance: 1000M Ohms Min @ DC 250V Current Rating: 1 Amp Dielectric Voltage: AC 500V for 1 Minute Operating Temp: -55° to 105° C Gold Plated Beryllium Copper Contacts

Dimensions:

A: 20.32 B:17.78 C: 10.16 D: 7.62

** Minimum purchase of 34 units **

Specifications:

Contact Resistance: 30M Ohms Max @ DC 100mA Insulation Resistance: 1000M Ohms Min @ DC 250V Current Rating: 1 Amp Dielectric Voltage: AC 500V for 1 Minute Operating Temp: -55° to 105° C Gold Plated Beryllium Copper Contacts

Dimensions:

A: 17.78 B:15.24 C: 10.16 D: 7.62

** Minimum purchase of 60 units **

Specifications:

Contact Resistance: 30M Ohms Max @ DC 100mA Insulation Resistance: 1000M Ohms Min @ DC 250V Current Rating: 1 Amp Dielectric Voltage: AC 500V for 1 Minute Operating Temp: -55° to 105° C Gold Plated Beryllium Copper Contacts

Dimensions:

A: 10.16 B:7.62 C: 10.16 D: 7.62

** Minimum purchase of 80 units ** Contact Resistance: 30M Ohms Max @ DC 100mA
Insulation Resistance: 1000M Ohms Min @ DC 250V
Current Rating: 1 Amp
Dielectric Voltage: AC 500V for 1 Minute
Operating Temp: -55° to 105° C
Gold Plated Beryllium Copper Contacts

A: 7.58
B: 3.08
C: 10.16
D: 7.62

** Minimum purchase of 12 units **

Specifications:

Contact Resistance: 30M Ohms Max @ DC 100mA Insulation Resistance: 1000M Ohms Min @ DC 250V Current Rating: 1 Amp Dielectric Voltage: AC 500V for 1 Minute Operating Temp: -55° to 105° C Gold Plated Beryllium Copper Contacts

Dimensions:

A: 50.78 B: 48.26 C: 17.72 D: 15.24

** Minimum purchase of 17 units **

Specifications:

Contact Resistance: 30M Ohms Max @ DC 100mA Insulation Resistance: 1000M Ohms Min @ DC 250V Current Rating: 1 Amp Dielectric Voltage: AC 500V for 1 Minute Operating Temp: -55° to 105° C Gold Plated Beryllium Copper Contacts

Dimensions:

A: 35.54 B: 33.03 C: 17.72 D: 15.24

** Minimum purchase of 17 units **

Specifications

Contact Resistance: 30M Ohms Max @ DC 100mA Insulation Resistance: 1000M Ohms Min @ DC 250V Current Rating: 1 Amp Dielectric Voltage: AC 500V for 1 Minute Operating Temp: -55° to 105° C Gold Plated Beryllium Copper Contacts

Dimensions:

A: 35.54 B: 33.03 C: 17.72 D: 7.62

** Minimum purchase of 20 units **

Specifications:

Contact Resistance: 30M Ohms Max @ DC 100mA Insulation Resistance: 1000M Ohms Min @ DC 250V Current Rating: 1 Amp Dielectric Voltage: AC 500V for 1 Minute Operating Temp: -55° to 105° C Gold Plated Beryllium Copper Contacts

Dimensions:

A: 30.46 B: 27.94 C: 17.72 D: 15.24

** Minimum purchase of 20 units **

Specifications:

Contact Resistance: 30M Ohms Max @ DC 100mA Insulation Resistance: 1000M Ohms Min @ DC 250V Current Rating: 1 Amp Dielectric Voltage: AC 500V for 1 Minute Operating Temp: -55° to 105° C Gold Plated Beryllium Copper Contacts

Dimensions:

A: 30.46 B: 27.94 C: 17.72 D: 7.62

** Minimum purchase of 24 units **

Specifications:

Contact Resistance: 30M Ohms Max @ DC 100mA Insulation Resistance: 1000M Ohms Min @ DC 250V Current Rating: 1 Amp Dielectric Voltage: AC 500V for 1 Minute Operating Temp: -55° to 105° C Gold Plated Beryllium Copper Contacts

Dimensions:

A: 25.38 B: 22.86 C: 10.14 D: 7.62

** Minimum purchase of 26 units **

Specifications:

Contact Resistance: 30M Ohms Max @ DC 100mA Insulation Resistance: 1000M Ohms Min @ DC 250V Current Rating: 1 Amp Dielectric Voltage: AC 500V for 1 Minute Operating Temp: -55° to 105° C Gold Plated Beryllium Copper Contacts

Dimensions:

A: 22.84 B: 20.32 C: 10.14 D: 7.62

** Minimum purchase of 30 units **

Specifications:

Contact Resistance: 30M Ohms Max @ DC 100mA Insulation Resistance: 1000M Ohms Min @ DC 250V Current Rating: 1 Amp Dielectric Voltage: AC 500V for 1 Minute Operating Temp: -55° to 105° C Gold Plated Beryllium Copper Contacts

Dimensions:

A: 20.3 B: 17.78 C: 10.14 D: 7.62

** Minimum purchase of 34 units **

Specifications:

Contact Resistance: 30M Ohms Max @ DC 100mA Insulation Resistance: 1000M Ohms Min @ DC 250V Current Rating: 1 Amp Dielectric Voltage: AC 500V for 1 Minute Operating Temp: -55° to 105° C Gold Plated Beryllium Copper Contacts

Dimensions:

A: 17.76 B: 15.25 C: 10.14 D: 7.62

** Minimum purchase of 80 units **

Specifications:

Contact Resistance: 30M Ohms Max @ DC 100mA Insulation Resistance: 1000M Ohms Min @ DC 250V Current Rating: 1 Amp Dielectric Voltage: AC 500V for 1 Minute Operating Temp: -55° to 105° C Gold Plated Beryllium Copper Contacts

Dimensions:

A: 7.56 B: 3.08 C: 10.14 D: 7.62

** Minimum purchase of 60 units **

Specifications:

Contact Resistance: 30m? Max @ DC 100mA Insulation Resistance: 1000M? Min @ DC 250V Current Rating: 1 Amp Dielectric Voltage: AC 500V for 1 Minute Operating Temp: -55° to 105° C Gold Plated Beryllium Copper Contacts.

Dimensions:

A: 10.14 B: 7.62 C: 10.14 D: 7.62

Plastic Insulated Horizontal

Plastic Insulated Vertical

Metal Shielded Horizontal

Metal Shielded Vertical

Suits W 3400 (4mm) & W 3410 (3mm) multicore coaxial cable. For crimper to suit, see T 1555 in the Tools section.

Female to female. Chassis mount.

Chassis mount. Suits RG58 coax. Chassis Hole 12mmØ

Crimp Type Plug to suit RG58

Crimp Type Plug to suit RG59

Crimp Type Plug to suit RG6

Insulated panel mount single hole
Solder type

Solder type. Suits RG58 Coax.

Panel mount single hole
Solder type

Chassis mount. Suits RG58 coax. 4 x 2mm Tapped holes, Chassis hole 12mm Ø.

Solder Type Plug to suit RG58

Crimp type plug to suit RG6 quad shield

90Deg. Solder Type Plug to suit RG58

Female-Female

Panel mount. Mounting Hole 15.5mm Ø

Panel Mount. Mounting Holes 3.5mm Ø Chassis hole 15mm Ø

Female-Female, Panel Mount. Mounting Hole 15.5mm Ø

Crimp plug to suit RG59 coax

Reduces RG8 to RG58 suits P 0503

Solder plug to suit RG8 coax

Solder plug to suit RG58 coax

Crimp plug to suit RG58 coax

Panel Mount Double Connector RG58

Single Hole Mount. Suits RG58 Coax

Single Hole Mount

Screw in Plug suits RG58 Coax.

Suits RG58 Coax

Austar approved

F Connector Male Screw On Gold Plated for hifi use

Male Plug RG11

Features integral crimp ring

As used for television antenna and standard 75 cabling. Simple to crimp one piece design. Uses the solid copper core of the cable as the center pin. Features integral crimp ring. Features integral crimp ring. Suits RG59 coaxial cable.



Cable Stripping Data


A: 4mm
B: 3mm
C: 8mm  

Feature integral crimp rings.

Feature integral crimp rings.

Fem/Fem Joiner

Socket Chassis Mount Single Hole

Mounting Hole 9.5mm Ø

75Ω

TNC Male to F Female Adaptor

PAL Female To RCA Male Adapter 

SCART to 3 x RCA & SVHS Socket.

Female RCA to female RCA by three. Typically used to extend an AV lead and as such has red, white and yellow colours for audio (red & white) and video (yellow). It can however be used for any application requiring 3 female to female RCA connections in an adaptor format.

RCA to 6.35mm Mono

RCA Male to F Connector Female Adapter

Dual Binding Posts - BNC Male Adaptor

3 Way T - BNC Sockets

Splitter BNC Male - 2 Females

Male to female BNC, 90deg. Right angle adaptor

Male Bayonet Neill Concelman/ British Naval Connector (BNC) to Female F-Connector in adaptor format.

BNC Female - BNC Female Adaptor

BNC Male - BNC Male Adaptor

BNC Skt to RCA Plug

BNC Female - RCA Male Adaptor

BNC to RCA Socket

BNC Male - RCA Female Adaptor

PL259 Male - BNC Female Adaptor

RCA to 6.35mm Stereo

BNC Male - PL259 Adaptor

Mono Plug

Stereo Plug

Rca Plug to 2 RCA Sockets

Stereo Plug

Stereo Plug

Mono Plug

Reliable adaptors for audio and video use.

Mono to RCA

RCA SOCKET TO RCA SOCKET

RCA Female - RCA Female Adaptor

RCA to 2 x RCA Skt

RCA to 1 x RCA Skt

Mono to RCA

2 x RCA Socket to 2 x RCA Socket

Suits W 3400 and W 3410 multicore coaxial cable. For crimper to suit see T 1555 in the tools section.

AMPHENOL (formerly Alcatel) connectors are ideal for use in high performance audio applications, including mobile PA use. They represent a no-compromise approach to connector technology, with rugged construction, secure mechanical characteristics and low induced noise levels.

Yellow Male RCA Plug

Cable Entry: 4-6mm

AMPHENOL (formerly Alcatel) connectors are ideal for use in high performance audio applications, including mobile PA use. They represent a no-compromise approach to connector technology, with rugged construction, secure mechanical characteristics and low induced noise levels.

White Male RCA Plug

Cable Entry: 4-6mm

AMPHENOL (formerly Alcatel) connectors are ideal for use in high performance audio applications, including mobile PA use. They represent a no-compromise approach to connector technology, with rugged construction, secure mechanical characteristics and low induced noise levels.

Red Male RCA Plug

Cable Entry: 4-6mm

AMPHENOL (formerly Alcatel) connectors are ideal for use in high performance audio applications, including mobile PA use. They represent a no-compromise approach to connector technology, with rugged construction, secure mechanical characteristics and low induced noise levels.

Black Male RCA Plug

Cable Entry: 4-6mm

AMPHENOL (formerly Alcatel) connectors are ideal for use in high performance audio applications, including mobile PA use. They represent a no-compromise approach to connector technology, with rugged construction, secure mechanical characteristics and low induced noise levels.

Yellow Female RCA Socket

Cable Entry: 4-6mm

AMPHENOL (formerly Alcatel) connectors are ideal for use in high performance audio applications, including mobile PA use. They represent a no-compromise approach to connector technology, with rugged construction, secure mechanical characteristics and low induced noise levels.

White Female RCA Socket

Cable Entry: 4-6mm

2-6mm cable entry size. Retractable, spring loaded outer sleeve. These RCAs feature a unique retractable sleeve which earths before signal contact to avoid unwanted noise upon connection. The sleeve after being screwed up also serves to lock the RCA in place insuring it will not accidently pull off.

2-6mm cable entry size. Retractable, spring loaded outer sleeve. These RCAs feature a unique retractable sleeve which earths before signal contact to avoid unwanted noise upon connection. The sleeve after being screwed up also serves to lock the RCA in place insuring it will not accidently pull off.

3 x 1 horizontal PCB mount RCA sockets.

2 x 2 Vertical PCB mount RCA sockets.

Specifications:

Mounting Depth: 24mm. PCB Holes: 0.6 x 1.5mm Row Pitch: 14mm.

2 x 1 Vertical PCB mount RCA sockets.

Specifications:

Mounting Depth: 24mm PCB holes: 0.6 x 1.5mm.

Gold plated single hole mount sockets. Insulated from chassis. Mounting hole 9.4mm Ø. Black identifying stripe

Gold plated single hole mount sockets. Insulated from chassis. Mounting hole 9.4mm Ø. Red identifying stripe

2 x 2 PCB mount RCA sockets. Gold plated contacts.

2 x 1 horizontal PCB mount RCA sockets. Gold plated.

2 x 1 PCB mount RCA sockets. Gold plated contacts.

2 x 2 PCB mount RCA sockets.

2 x 1 PCB mount RCA sockets.

Single PCB RCA socket.

Low Profile

4 way panel mount socket. Insulated from chassis with individual solder tag connections.

2 Way panel mount socket. Insulated from chassis with individual solder tag connections

Mono to Stereo

Male 3.5mm stereo jack to two female 3.5mm jacks.

Mono to Mono

Allows easy connection from both sides via 3.5mm TRS connection. Ideal for custom AV wall plates or as a cable joiner. 12mm mounting hole. Stereo.

Stereo to Stereo

Mono Plg to Stereo Skt

3.5mm aircraft seat adaptor. Allows you to use your own headphones in many commercial airliners. 2 x 3.5mm mono plug to 3.5mm stereo socket.

Reliable adaptors for audio and video use.

Mono to Mono

Stereo to Stereo

Stereo to Stereo

Gold plated Dual banana plug for speaker connections. With screw connection for wire termination.
3A @ 125V AC.

With screw connection for wire termination. 3A @ 125V AC.

With screw connection for wire termination. 3A @ 125V AC.

Car Radio Antenna Plug Insulated

Car Radio Antenna Plug

Car Radio Antenna Socket Insulated

Car Radio Antenna Socket

75 Ohm Chassis Socket

75Ω Male to male Pal adaptor

75Ω Female to female Pal adaptor

Metal 75 ohm PAL line plug to suit RG59 coaxial cable. Crimp type.

Metal Line Socket to suit RG59

75 Ohm Chassis Socket

Metal Line Plug to suit RG59

Metal 75 ohm PAL plug to suit RG6 size coaxial cable. Screw together design for easy connection.

6.35mm insulated PCB mount stereo socket with SPST switched contact. Mounting hole 11mmØ

6.35mm insulated PCB mount mono socket with SPST switched contact. Mounting hole 11mmØ

Stereo PCB Mini DPST

Stereo PCB mount, DPST.

Stereo PCB DPST

Stereo Chassis DPST

Mono Chassis SPST

2.5mm mono chassis mount socket.
Switched contact.

3.5mm Gold Audio & Video
Cable Entry : 4.5mm

3.5mm Gold Plated Stereo Line Socket

3.5mm Stereo

3.5mm Mono

Socket jack, 6.35 metal stereo.

6.35mm Line Stereo

Socket jack, 6.35 metal mono.

6.35mm Line Mono

Plug with switch

Line Plug

Plug & Fuseholder

Line Socket

28mm mounting hole. 60 x 42.5mm mounting facia included (can be used without facia if required). Rubber cap prevents dust buildup inside connector.

2 X Skt to Plug

Heavy duty 4 pin plug as used on professional amplifiers and speaker boxes. Handles up to 30A current. Accepts up to 8mmØ cable.

These XLR style connectors feature sturdy metal construction, high quality contact inserts and strain relief grommets on the line connectors. The plugs have an internal sleeve which tightens around the cable as the plug is screwed together, securing the cable to prevent “pulling out”. This improves their service life and reliability. They are fitted with the standard XLR locking mechanisms, ensuring a reliable contact.

These XLR style connectors feature sturdy metal construction, high quality contact inserts and strain relief grommets on the line connectors. The plugs have an internal sleeve which tightens around the cable as the plug is screwed together, securing the cable to prevent “pulling out”. This improves their service life and reliability. They are fitted with the standard XLR locking mechanisms, ensuring a reliable contact.

These XLR style connectors feature sturdy metal construction, high quality contact inserts and strain relief grommets on the line connectors. The plugs have an internal sleeve which tightens around the cable as the plug is screwed together, securing the cable to prevent “pulling out”. This improves their service life and reliability. They are fitted with the standard XLR locking mechanisms, ensuring a reliable contact.

Dimensions:

These XLR style connectors feature sturdy metal construction, high quality contact inserts and strain relief grommets on the line connectors. The plugs have an internal sleeve which tightens around the cable as the plug is screwed together, securing the cable to prevent “pulling out”. This improves their service life and reliability. They are fitted with the standard XLR locking mechanisms, ensuring a reliable contact.

Dimensions:

These XLR style connectors feature sturdy metal construction, high quality contact inserts and strain relief grommets on the line connectors. The plugs have an internal sleeve which tightens around the cable as the plug is screwed together, securing the cable to prevent “pulling out”. This improves their service life and reliability. They are fitted with the standard XLR locking mechanisms, ensuring a reliable contact.

These XLR style connectors feature sturdy metal construction, high quality contact inserts and strain relief grommets on the line connectors. The plugs have an internal sleeve which tightens around the cable as the plug is screwed together, securing the cable to prevent “pulling out”. This improves their service life and reliability. They are fitted with the standard XLR locking mechanisms, ensuring a reliable contact.

(Designed by Dontronics) AVR chips are a new range of micro-controllers that boast faster operating speeds and a larger instruction set than other micro-controllers. The AVR development series of Kits designed by Dontronics are designed to be an inexpensive method of prototyping projects using the Atmel AVR range of micro-controllers. The K 9510 is suitable for programming and prototyping projects using the 20 pin series of Atmel AVR micro-controllers. The K 9515 has been designed as a development platform which suits a wider variety of the AVR I.C., including the 8, 20 and 28 pin AVR micro-controllers. The K 9515 may also act as a mother board for the K 9510 . Each kit is supplied with a AVR micro-controller and all the necessary components to begin prototyping your first micro-controlled project immediately.

(October 04 SC) This SMS controller allows you to be notified anywhere in the world when a particular condition occurs (for instance, you could use it to notify you when your house alarm triggers, or any time automated equipment starts). It also allows you to return SMS's to the unit effectively "controlling" the device its attached to. So this means you could switch equipment on and off or even perform specific tasks anywhere around the globe!

This kit is designed to operate with the Nokia 3210, 3310, 5110 and 6110 because of their common serial data interface control. These phones are relatively common on the second hand market and can easily be sourced online via Ebay etc.

Before buying this project be aware of the limitations the SMS network presents. It does not allow real time control of devices, SMS's may take anywhere between a few seconds to tens of seconds to be delivered. This means it is not suitable for rapidly changing inputs. Secondly, be sure to use the kit with a pre-paid phone ensuring any malfunctions that could possibly occur doesn’t cost you a fortune.

An additional use would be to mount it in your car in conjunction with your car alarm to provide not only notification when your alarm sounds, but also the ability to shut the car down if wired into your immobiliser appropriately. This kit literally has endless applications!

Features

Works with popular Nokia brand phones Eight open collector outputs Four digital inputs User programmable plain text message controls Communicate from any other mobile Password protection On-board phone power supply Perfect for alarm panels Can be utilised in cars as a mobile alarm notification/ECU shutdown device

(SC July ’01) A simple to build alarm clock with all the bells and whistles. Featuring a 4 digit 12 hour display with AM/PM indicator. A melody alarm sounds at the set time to provide a wake up call / reminder. Convenient push buttons allow the unit to be set up. Powered by a 12V 300mA DC plug pack (M 9271)

Get the most out of your exercise program with this heart rate monitor project.

If you over exert yourself, you might be doing damage, if you under exert it doesn't help improve your condition that much.
This project monitors your heart rate and provides a handy timer to assist your fitness program.
Feature packed and easy to build this project will be an enhancement to any exercise regime.

Features:

• Adjustable timer with audible alarm • Visible pulse indicator • Timer end buzer • Timer stops when pulse drops below minimum pulse beat rate • Start/ Stop timer control • Error display for no pulse • Minmum and maximum pulse settings with audible alarm • Recovery display 1,2,3,4,& 5 minutes • Supplied with professionally screened and punched case • Powered by a 9- 12V 300mA plug pack

Say you want a 9V battery to supply 40mA to a circuit. That's a pretty modest current but if you use a PP3 style 9V battery it won't last long at all. In fact, if you're using a typical “heavy duty" 9V battery, it will last less than 20 minutes before the voltage drops to 7.8V. That may be enough to stop your circuit working. Or maybe you are using an alkaline type. Depending on the brand and price, you might get about two hours life. Not good.

By comparison, two AA alkaline cells driving this DC-DC Converter circuit to give 9V at 40mA will last about 7 hours. And rechargeable AA cells can be even offer better performance.

This circuit can deliver up to 90mA at 9V (with less life from the cells) or can be set to deliver anywhere between 4.5V and 20V. You might never have to buy another 9V battery ever again.

(SC June ‘03) A DC-DC converter can allow you to run equipment in your car that requires more than the 12 volts a car battery can supply. This makes it ideal for those who need to run laptops on the road. Adjustable from 13.8V to 24V at a maximum of 2A. It can even charge SLA batteries (12V 6.5Ah or bigger).

(SC April ‘03) This handy kit can be hooked up to a regular modem and send a warning tone whenever your alarm is triggered. This means you can add a dial warning facility to your existing alarm system. Or alternatively it could be used to provide warnings during failures in equipment, machinery, air conditioning systems, computers etc.

Features

• PIC microcontroller based • Can monitor NO, NC contacts or an external voltage • Alarm reset output • Utilises a standard modem to make calls • EEPROM storage of settings • 12V AC or DC operation"

This multi-purpose timer operates from a 12V supply and offers accurate timing periods ranging from 0.1s to 16.5 minutes. Ideal for use in cars ie: to run cooling fans, security features etc.

Features:

- Triggered on rising or falling voltage (user selectable) - One-shot or alternating (pulse) operation - Pulse mode can be set for variable on/off periods - Precise 0.1s to 16.5-minute timing period - Relay output with dual double-throw contacts rated at 5A - LED indicator for timing

Incorporating the new super accurate DS18B20 digital temperature sensor, this thermometer/thermostat kit provides an accurate reading to 1 decimal point. The LCD shows current, min and max temperatures. An internal buzzer sounds whenever over temperature or under temperature limits are exceeded. Ideally suited for monitoring air conditioners, cool rooms, wine cellars. Or activating fans, heating/cooling equipment. With onboard programming socket and free downloadable software (BASCOM) changes can easily be made to the program if required. (see web site for firmware and software).

Features

• Sensor can be wired up to 300m away • Measures from -55°C to +125°C • 0.1°C accuracy from -10°C to +85°C • N/O or N/C contacts, plus buzzer alert for over and under alarms • Adjustable hysterises to stop output oscillation • Requires 12V DC plugpack

(SC May ’94) Servo motors require a continuous stream of pulses to control them, where the pulse width determines the servos position. Unless you have a circuit to generate this pulse stream, your servo motors cannot be controlled. This kit provides two such circuits on two separate PCBs with all components. Essentially, this kit gives you control over a servo motor with a potentiometer as your controller.
Dimensions : 41x 35 x 12 mm and 40 x 50 x 13 mm

(EA July ’96) Anomalies in mains power waveforms can cause 'unexplained' faults in equipment from audio amps to computers, and serious damage in some cases. This kit uses an L-C network to eliminate any spikes, pops, and glitches in the AC mains, giving your valuable equipment a filtered, clean supply. It simply connects in series between equipment and the mains socket. Includes screened and punched Jiffy box case.

Protect your valuable computer or audio equipment from mains glitches and spikes!

(SC Sep-Oct ‘08) The ultimate D-I-Y model railway controller. Latest design offers infra red remote control, pulse power for realistic low speed train movement, speed bargraph, adjustable braking inertia and much more! 16-17V output up to 6A.

(SC January ‘09) Want to try your hand at ‘stop motion’ photography? This camera shutter/flash controller allows you to take a picture at a precise moment between 1ms and 9.99s after a trigger. Triggering can be from the included electret mic (to pick up sound ‘events’) or other sensors like a PIR detector, light-beam interrupter, or custom sensor switches (not included).

Specifications:

Trigger inputs: electret microphone or external trigger (via PIR sensor etc) Delay time: 0 to 999ms in 1ms increments or 0 to 9.99 seconds in 10ms increments Timing Accuracy: 1ms or 10ms Outputs: (1) Non-delayed triggering for external shutter release (2) Delayed triggering for electronic flash Power: 9V alkaline battery Consumption: 16mA (standby); 30mA when triggered

Extra credit card style tag for K 9300 RFID Entry Kit

Essentially, the system consists of a reader module and one or more "tags". Based on RFID (Radio Frequency Identity) technology, each tag is encoded with a unique identity.
When a tag is brought within range of the reader, it is energised by the reader's magnetic field. It then transmits its unique code to the reader, which validates the code and arms or disarms the alarm system accordingly.
This system also includes the ability to operate an electric door strike. A simple wave of your hand and an "Open Sesame" incantation are all that are required for the door to your castle to spring open!

Features

Contactless operation 90-100mm detection range No batteries (in tags) to go flat Stores up to 24 tag ID codes Easy tag addition & removal Works through any non-metallic material Audio feedback via on-board beeper Tamper detection Arm & alarm outputs Electric door strike output Suitable for home or car use Requires 12V DC @ 40mA (nominal)

Need to design around 28 or 40 pin PIC? Can’t find a reasonably priced programming kit? We’ve managed to solve BOTH problems with these great add ons for the K 9505. They allow you to easily program 28 & 40 pin PIC’s which are very popular in electronics.
Each kit includes a ZIF socket and PIC chip.

Need to design around 28 or 40 pin PIC? Can’t find a reasonably priced programming kit? We’ve managed to solve BOTH problems with these great add ons for the K 9505. They allow you to easily program 28 & 40 pin PIC’s which are very popular in electronics.
Each kit includes a ZIF socket and PIC chip.

(SC September ‘03) This new revision of the PIC programmer can now be taken on the road with you. It is powered by either a 9V battery or plugpack. It’s capable of programming many chips such as 8 & 18 pin versions of PIC16F & PIC12F, 28 & 40 pin PIC16F87X series and 24CXX EEPROMS. Beware of cheaper kits which do not included zif socket, programming cable and 18 pin PIC16F chip.

Mood lighting is very popular these days, with most new homes having at least one light dimmer installed. With this useful project a light can be turned on, turned off, or adjusted up or down with either the touch of your hand or by a remote control. The unit is attractive and unobtrusive and will suit the decor of most walls. Remote control not included, A1013 is recommended.

 

Features

• Attractive aluminium wall plate • 10 separate outputs • Acknowledgment LED • 240V AC operation • Last dimming setting stored • Soft start to extend globe life • RFI suppression • Touch plate dimming • Full brightness restored on second touch

(SC November ‘08) This small circuit can be used as a speed controller for a 12V motor rated up to 5A (continuous) or as a dimmer for a 12V halogen or standard incandescent lamp up to 50W. It varies the power to the load (motor or lamp) using pulse width modulation.

(SC June ‘03) The sunset switch kit can turn your equipment on or off according to lighting conditions. It is ideal for activating garden lighting at dusk or turning lights on indoors whilst you’re away on holiday. It features an optional timeout (15 min, 1hr, 2hr, 4hr), manual on/off switching and 6A (240VAC) rating. You could switch up to 1440W of appliances or lighting on and off!

Ideal way to control the speed of a high current DC motor without the need for expensive gearboxes or inefficient resistors.

Features

• Design incorporates PIC micro and efficient MOSFET’s • Excellent speed regulation under load • Soft start • 8 memory settings • Battery level meter • Low battery alarm • Variable pulse width modulation • 12-24V DC input

Allows transmission of audio over UTP cable, such as Cat5e or 6.
Range up to 1.5km. Requires 12VAC.

(SC June ‘01) If your home or business has more than one CCTV security camera you will want an automatic scanner that switches between the cameras so you can see what’s happening, all on a single monitor. The K 5842 does all this with adjustable scan rate and provision for audio switching.

Features

• RCA input and output connectors • Audio and Video scanning • Pause button • Adjustable scan rate • LED position indicators

(EA Nov ’99) This useful kit can be used to sequence through (audio and video) up to four different cameras and connect them to a standard monitor. The sequencing rate can be adjusted and a pause button or switch can easily be added to stop the sequence temporarily.

(EA Nov ’97) Ever transferred your home or holiday movies to VHS and found the picture quality is degraded? This little enhancer will spruce up the video signal, and can even improve the quality of poorly-recorded video. It also has an image stabiliser which removes all the invisible overheads from video signals, such as teletext data, leaving a clean PAL composite signal. Supplied in a professionally screened and pre-punched instrument case and powered by 240V mains power. If you're into making your own movies, this kit is very useful!

(SC May ’02) This little LED chaser kit is super easy to build and provides a bright addition to any shop display or vehicle. It features 32 bright LED’s which glow red. Built into it’s PIC micro controller are 12 patterns which can be selected at the press of a button. Speed is adjustable via an on board trimpot.

Requires 12VDC supply

Features

• 12 switch selectable light patterns • Adjustable pattern speed • Adjustable LED brightness • 2 pattern medleys

(SC March ’94) Here is a project that will really catch your eye. It uses 10 Light Emitting Diodes and flashes them two at a time in a clockwise direction. It is a simple kit to construct and provides an effective display. The rate of the chase can be varied by the potentiometer mounted on the PCB. Requires external 6 Volts DC.
Try it with our 10mm high intensity LEDs. Great for shop window displays!

Add a second tube to the K 5792 Beat Triggered strobe to double the lighting output.
Contains the Xenon tube and 250V capacitors and all the other components required to modify the K 5792 kit.

(EA May ’99) With this kit you can take any stereo signal and create a low cost surround sound setup. It enhances a stereo signal by extracting the ‘hidden’ front centre and rear ambience channels and a subwoofer output. An adjustable time delay for the rear channel which can be configured to 0,15,20,25 and 33 millisecond settings adds to the surround sound effect. All outputs are line level, so each channel must be connected to an amplifier to provide speaker level outputs.

(EA May ‘92) This great kit enables you to customise your sound system. The circuit simply connects between the audio source and the amplifiers. There are two outputs, one for bass and another provides signal for the upper range. Thus each amp is dedicated to a frequency range (i.e. one for bass, one for midrange and treble). Because no passive crossover is required there are no losses involved. Suitable for live PA or Hi-Fi applications. One per channel is required. Operates on ±15V rails. The result is much better sound with less distortion. Comes with a range of resistors to select the crossover frequency between 1.8kHz and 3.6kHz.

(EA Sept ‘99) This kit can be used to get the most out of your sub-woofer or low-bass speaker system. It can be used to compensate for poor or ‘peaky’ subwoofer response, improve the low-end extension in a speaker and even reduce a subwoofer driver’s cone travel. It features a bypassable subsonic filter set to 20Hz, a variable low-pass filter, a variable gain(+/-12dB) input stage plus dual-phase outputs for running amplifiers in bridged mode.

(SC July '08) This updated design allows multichannel amplifiers to be bridged into a single high power channel. Get double the power from your stereo amplifier!

This fantastic design includes an active filter for adjustable frequency cut off, volume control, preamplifier and phase shifter allowing the driving of amplifiers in either bridge or single configuration. It also features compressor limiting which means no harsh clipping if over-driven and an automatic power up / power down in response to the audio input. For maximum compatibility it can be driven from either speaker or line level. The PCB can be housed remotely within the sub-woofer cabinet with its amplifier or at the main equipment rack with a separate sub-woofer amplifier. Note: K5562 requires 12V AC power supply M9666 (Not included).

Specifications

Harmonic Distortion: 0.005% Signal to Noise Ratio: -84dB @ 300mV Input Impedance: 10k Ohms Output Impedance: <1k Ohms Max Output Voltage: 6V RMS Cut Off Frequency Range: 60Hz to 130 Hz Filter Slope: 12dB /octave Dimensions 163 x 90 x 32

(SC April 2005) Can provide nearly an extra octave of bass response from your existing hi-fi speakers. Suitable for sealed and vented enclosures it is sure to supply an added boost to your hi-fi or home theatre. Supplied with a blank jiffy box case.

(SC Sept. ’94) Compact miniature design uses only one IC to switch a relay. This versatile Vox circuit is triggered whenever a noise or sound is made (via the microphone) causing a relay to close for a preset time. The circuit features an almost instant turn on time with a 3 second delay before release. Requires 12V DC supply. Ideal for CB or Amateur Radio

(EA April ’82) This versatile Vox circuit is triggered whenever a noise or sound is made causing a relay to close for a preset time. Requires 12V DC supply and microphone. Reaction sensitivity and on time are fully variable. Optional manual over-ride.

Suggested Uses

• Controlling tape recorders • Slide projectors • Eliminate the need for a press to talk button on transmitters • Turn on external porch lights • Paging systems • Hands free intercom switch-over

Ever wanted to play your guitar through your headphones along with your favourite music at the same time? Well now you can with the guitar jammer. Just plug the CD and guitar into this kit and you can play along with the best of them.

Features:

Low noise circutry Separate CD & Guitar volume controls Frequency response: -3db @ 30Hz and 70Hz 9V battery operated or 9VDC plugpack operated Suplied with professionally finished & screened case

This kit will amplify a microphone (low level signal) to a line level to connect into an amplifier. It features high performance with a balanced mic input as well as two auxiliary inputs which are all mixed. It can be configured to operate from either a single ended power supply (12V to 40V DC), or a split rail power supply (±15V to ±40V DC), making it ideal to build into any existing amplifier.

 

Specifications

Mic Gain 59.5dB Mic S / N Ratio -74dB A-weighted 50½ balanced source Mic Frequency Response 180Hz to 20kHz Aux Gain 13.5dB Aux S /N Ratio -99 dBA A-weighted 600½ unbalanced Aux Frequency Response 30Hz to 20kHz

(SC Mar ‘99) This handy kit can be used for a host of different audio effects such as compression, automatic level control, sustain and limiting. This low noise and distortion design can be used with a guitar, microphone or any other low-level signal source. Other features include adjustable compression ratio, adjustable limiting, adjustable gain and adjustable output level.

Specifications

Gain Control: 0dB-20dB Threshold control at 0dB Floor noise: -30mV Ratio Control: 1:1-15:1 Limit Control at 0dB gain 1:1 ratio 10mV-600mV Total harmonic distortion @ min. gain 0.16%@1kHz, 1.2%@10kHz Frequency response: -3dB @ 20kHz and -1dB @ 30kHz

(SC June 2008) If you need to send audio over long distances this kit can convert unbalanced line level signals to balanced. Perfect for preventing hum and noise. The kit can also convert balanced signals to unbalanced

Specifications

Signal to noise: ..................................................-100dB (1V output, 4.7kohm load) Frequency response: ..........................................-3dB @ 2Hz to 200kHz Power supply: ....................................................9V to 30V DC or +/-9V to +/-15V AC

PREAMP RIAA SHORTFORM

Add’s a RIAA phono input to any amplifier and allows easy line level recording to CD or MP3. Prevent the deterioration of your favourite vinyl and revisit those golden oldies and classics by converting them to MP3. This compact device allows easy connection from turntable to PC.

Features

• Can be equalised to suit various types of 45’s, 78’s and LP’s • Low signal to noise • RCA input & output

Remote control volume module to suit the K 5500 Silicon Chip Studio Series Pre-Amplifier.

This board allows infra red remote control of both volume level and input selection. Easy to build.

Infra-red volume control utilises Philips RC5 protocol. This remote control code is typically available on most universal remote controls. We recommend the A1013 referenced in the instructions for this kit.

Ultra low noise, low distortion design.
Drives high and low impedance headphones. Great for those requiring a bit more listening “oomph” from their portable MP3 player or CD player. Features dual headphone outputs.

Part of the K 5500 Studio Series Pre Amp - Published in Silicon Chip Magazine

Utilising the latest ultra low noise high peformance op amps. Featuring 5 RCA inputs plus easy integration with the headphone amplifier & power supply module. Unbelievably low 0.0005% distortion! Supplied with PCB, components, input rotary switch, volume pot & cabling.

Part of the K 5500 Studio Series Pre Amp - Published in Silicon Chip Magazine

A low noise linear power supply module to suit the Silicon Chip Studio Series Pre Amp. Easy to build and integrate into your pre amp project!

Part of the K 5500 Studio Series Pre Amp - Published in Silicon Chip Magazine.

(SC September 05) An ultra-fidelity, low distortion stereo pre-amplifier. So good is the design, it is suitable for use as a Class A amplifier front end. All the inputs are relay switched at the back of the unit, ensuring an absolute minimum of signal distortion and colouration. The state of the art design includes an infra-red remote volume control with mute function and input selection. Front panel controls are soft touch tactile switches for input selection and a motorised volume control. The ultrafidelity headphone amplifier provides exceptional audio performance. The pre-amplifier is supplied with a professionally CNC punched and silk screened chassis. This is the ultimate audiophile DIY pre-amplifier with performance equal or better to commercially available products costing several times the price.

Infra-red volume control utilises Philips RC5 protocol. This remote control code is typically available on most universal remote controls. We recommend the A1013 referenced in the instructions for this kit.

(ETI Oct ‘83) This easy to build universal level meter displays a peak reading from -21dB to 6dB in either dot or bar mode. Great for the car, home Hi Fi, disco console, mixers, audio monitoring. Operates from 7 to 15V DC.

This unit monitors the bass present on your home or car stereo. It monitors level and frequency for 2-1/2 octaves displaying them on four LED bargraph displays. It is easy to build and with a minimum of circuitry won't add additional noise to the base. Supplied complete with professionally screened and punched jiffy box.

(SC Feb ’03) Based on our best selling C 7100 public address unit! This portable PA module can be built into a speaker cabinet to provide a portable sound solution. It can run off 240V mains or a 12V SLA battery making it ideal for use just about anywhere. Two microphone inputs are provided via XLR/6.35mm combination sockets. Line inputs and outputs are handled by either RCA or 6.35mm jack connections. This makes it ideal for use with a guitar. Each input has individual volume controls in addition to universal bass and treble levels for all inputs. A battery charger module is available separately to provide charging of 12V batteries (where used). This kit is in short form only, it does not include speaker, batteries or parts for cabinet.

WOODEN CABINET NOT SUPPLIED.

Features

• Portable 12V battery powered unit • 33W RMS into 4 ohms • 2 combination 3 pin XLR/6.35mm mic inputs • 6.35mm guitar/aux input • Stereo RCA line inputs • Short form version only, includes PCB’s, components and metalwork.

A high-torque motor with a 42:1 ratio worm drive and double ended output. Fitted to an aluminium sub chassis with mounting holes for simple installation into your project. The 125mm wide 3mm diameter axle is fitted with plastic bushings in the chassis. Great for toy car projects or for powering a small robotics experiment. Powered by 3 to 6V DC.

A 120:1 ratio reduction motorised gearbox, powered by 3 to 6V DC. Fitted with a “keyed” output stub shaft with 2mm diameter hole.

A worm-drive gearbox powered by 3 to 6V DC with a 90° double ended 3mm diameter shaft similar to a car axle. Mounted in a plastic sub-chassis with four mounting holes for easy installation into a project. 42:1 reduction ratio. Axle width 125mm end to end.

** Minimum purchase of 10 units ** Metal driveshafts for making customised drive designs in robots, etc.

** Minimum purchase of 10 units ** Metal driveshafts for making customised drive designs in robots, etc.

** Minimum purchase of 10 units ** Metal driveshafts for making customised drive designs in robots, etc.

A selection of useful plastic gears, pulleys and cams for building and experimenting in mechanics. Kit contains 2 x 12 tooth drive pinions, 2 x 20 tooth gears, 2 x 30 tooth gears, 2 x 40 tooth gears, 4 pulleys (10mm, 20mm, 30mm and 40mm diameter), 2 x eccentric cams, 2 x snail cams, 2 x small pear cams and 2 x large pear cams. The drive pinions fit a 2mm motor output shaft. The gears and the drive-centre of the cams are a press-fit onto a 3mm axle, pulleys press-fit onto a 3.2mm shaft.

Contains two 28mm wide rubber caterpillar tracks and 8 colourful 40mm diameter drive wheels (two wheels are required per track end). Wheels are a press-fit onto the output shafts of J 0012, J 0018 and J 0020 motorised gearboxes. Track length suits a 145mm wheelbase. Great for creating toy projects or an all-terrain robot!

Clamps two TO-220 devices to a heatsink.

Clamps two TO-220 devices to a heatsink.

Clamps a single TO-220 device to a heatsink.

Mounting hole 3.2mm.

Clamps a single TO-220 device to a heatsink.

Mounting hole 3.2mm.

Clamps 2 transistor packages onto a heatsink. Mounts via a 4mm bolt. Two models available.

TO220/TOP3 Transistor Bush Packet of 1000.

Clamps 2 transistor packages onto a heatsink. Mounts via a 4mm bolt. Two models available.

Simple push-on installation. Insulates the TO-3 transistor case to prevent accidental short circuits.

Bushes Only

Pk 100

Bushes Only

TO-3 Pk 200

New adhesive silicon washers now available simplifying installation. Complete insulating kits include washers and bushes for mounting 4 devices (2 bushes per TO-3). Washers and bushes are available in bulk packs separately.

New adhesive silicon washers now available simplifying installation. Complete insulating kits include washers and bushes for mounting 4 devices (2 bushes per TO-3). Washers and bushes are available in bulk packs separately.

Silicon washers only

TO-126 Pk 100

Complete insulating kits include washers and bushes for mounting 4 devices (2 bushes per TO-3).

TO-126 Pk 4

New adhesive silicon washers now available simplifying installation. Complete insulating kits include washers and bushes for mounting 4 devices (2 bushes per TO-3). Washers and bushes are available in bulk packs separately.

New adhesive silicon washers now available simplifying installation. Complete insulating kits include washers and bushes for mounting 4 devices (2 bushes per TO-3). Washers and bushes are available in bulk packs separately.

Silicon washers only

TOP-3 Pk 100

Complete insulating kits include washers and bushes for mounting 4 devices (2 bushes per TO-3).

TOP-3 Pk 4

Mica washers only

TOP-3 Pk 100

Complete insulating kits include washers and bushes for mounting 4 devices (2 bushes per TO-3).

TOP-3 Pk 4

New adhesive silicon washers now available simplifying installation. Complete insulating kits include washers and bushes for mounting 4 devices (2 bushes per TO-3). Washers and bushes are available in bulk packs separately.

New adhesive silicon washers now available simplifying installation. Complete insulating kits include washers and bushes for mounting 4 devices (2 bushes per TO-3). Washers and bushes are available in bulk packs separately.

New adhesive silicon washers now available simplifying installation. Complete insulating kits include washers and bushes for mounting 4 devices (2 bushes per TO-3). Washers and bushes are available in bulk packs separately.

Silicon Washers Only Pk 1000

Silicon washers only

TO-220 Pk 100

Complete insulating kits include washers and bushes for mounting 4 devices (2 bushes per TO-3).

TO-220 Pk 4

Mica washers only

TO-220 Pk 100

Complete insulating kits include washers and bushes for mounting 4 devices (2 bushes per TO-3).

TO-220 Pk 4

Silicon washers only

TO-3 Pk 100

Complete insulating kits include washers and bushes for mounting 4 devices (2 bushes per TO-3).

TO-3 Pk 4

Mica washers only

TO-3 Pk 100

Complete insulating kits include washers and bushes for mounting 4 devices (2 bushes per TO-3).

TO-3 Pk 4

Handheld 4 piece enclosures molded from ABS plastic. They feature a satin textured finish with
two soft rubberised outer panels for extra grip. Battery compartment models include battery snap and clip in contacts.

Handheld 4 piece enclosures molded from ABS plastic. They feature a satin textured finish with
two soft rubberised outer panels for extra grip. Battery compartment models include battery snap and clip in contacts.

Designed for housing electronic control circuitry for use in industrial applications. Supplied complete with PCB mount terminals. Clip in top section is removable for access to PCB. Suits 35mm top hat DIN rail mount via the integral mounting bracket. Dinkle DME series. Each enclosure houses a single PCB.

Designed for housing electronic control circuitry for use in industrial applications. Supplied complete with PCB mount terminals. Clip in top section is removable for access to PCB. Suits 35mm top hat DIN rail mount via the integral mounting bracket. Dinkle DME series. Each enclosure houses a single PCB.

Designed for housing industrial control circuitry. The design includes integral PCB mounted terminals for ease of access and wiring once assembled. Each enclosure includes terminals and DIN rail mounting base, which suits 35mm top hat and asymmetrical “G” Type DIN rail mounts. Simple slot & screw together design. Dinkle DEGH series. 24 Way houses 2 PCB’s in the single enclosure.

Designed for housing industrial control circuitry. The design includes integral PCB mounted terminals for ease of access and wiring once assembled. Each enclosure includes terminals and DIN rail mounting base, which suits 35mm top hat and asymmetrical “G” Type DIN rail mounts. Simple slot & screw together design. Dinkle DEGH series. 12 Way houses single PCB.

Designed for housing industrial control circuitry. The design includes integral PCB mounted terminals for ease of access and wiring once assembled. Each enclosure includes terminals and DIN rail mounting base, which suits 35mm top hat and asymmetrical “G” Type DIN rail mounts. Simple slot & screw together design. Dinkle DEGM series. 12 Way houses 2 PCB’s in the single enclosure.

Designed for housing industrial control circuitry. The design includes integral PCB mounted terminals for ease of access and wiring once assembled. Each enclosure includes terminals and DIN rail mounting base, which suits 35mm top hat and asymmetrical “G” Type DIN rail mounts. Simple slot & screw together design. Dinkle DEGM series. 6 Way houses single PCB.

Base sections for DIN modules. Simply add section lengths together to obtain the required length of rail for your PCB.

107mm PCB width, overall width 112.7mm.

Calculating Total DIN Rail Length The total PCB length that can be accommodated by a given section can be calculated by totalling up the total length of the base sections and adding 10mm for each endcap. Eg: 2 x 44.8mm bases and 1 x 11.2mm section + endcaps = 44.8 + 44.8 + 11.2 + 10 + 10 = 120.8mm

Base sections for DIN modules. Simply add section lengths together to obtain the required length of rail for your PCB.

107mm PCB width, overall width 112.7mm.

Calculating Total DIN Rail Length The total PCB length that can be accommodated by a given section can be calculated by totalling up the total length of the base sections and adding 10mm for each endcap. Eg: 2 x 44.8mm bases and 1 x 11.2mm section + endcaps = 44.8 + 44.8 + 11.2 + 10 + 10 = 120.8mm

Base sections for DIN modules. Simply add section lengths together to obtain the required length of rail for your PCB.

107mm PCB width, overall width 112.7mm.

Calculating Total DIN Rail Length The total PCB length that can be accommodated by a given section can be calculated by totalling up the total length of the base sections and adding 10mm for each endcap. Eg: 2 x 44.8mm bases and 1 x 11.2mm section + endcaps = 44.8 + 44.8 + 11.2 + 10 + 10 = 120.8mm

Base sections for DIN modules. Simply add section lengths together to obtain the required length of rail for your PCB.

72mm PCB width, overall width 77.5mm.

Calculating Total DIN Rail Length The total PCB length that can be accommodated by a given section can be calculated by totalling up the total length of the base sections and adding 10mm for each endcap. Eg: 2 x 44.8mm bases and 1 x 11.2mm section + endcaps = 44.8 + 44.8 + 11.2 + 10 + 10 = 120.8mm

Base sections for DIN modules. Simply add section lengths together to obtain the required length of rail for your PCB.

72mm PCB width, overall width 77.5mm.

Calculating Total DIN Rail Length The total PCB length that can be accommodated by a given section can be calculated by totalling up the total length of the base sections and adding 10mm for each endcap. Eg: 2 x 44.8mm bases and 1 x 11.2mm section + endcaps = 44.8 + 44.8 + 11.2 + 10 + 10 = 120.8mm

Base sections for DIN modules. Simply add section lengths together to obtain the required length of rail for your PCB.

72mm PCB width, overall width 77.5mm.

Calculating Total DIN Rail Length The total PCB length that can be accommodated by a given section can be calculated by totalling up the total length of the base sections and adding 10mm for each endcap. Eg: 2 x 44.8mm bases and 1 x 11.2mm section + endcaps = 44.8 + 44.8 + 11.2 + 10 + 10 = 120.8mm

Mounting base section for DIN modules. This section is the mounting "foot" for attaching a series of bases to the rail. Suits standard top hat, miniature top hat and asymmetric “G” types.

Mounting base section for DIN modules. This section is the mounting "foot" for attaching a series of bases to the rail. Suits standard top hat, miniature top hat and asymmetric “G” types.

Endcaps to suit standard DIN rails. Accommodates 10mm of PCB length.

Endcaps to suit standard DIN rails. Accommodates 10mm of PCB length.

For mounting enclosures and project boxes to DIN rails. 30mm mounting hole spacing. Can be mounted to almost any size or type of enclosure. 

These contemporary designed all-steel speaker stands feature sturdy tubular risers and may be used for either front main or surround speakers. Base spikes decouple the stand from the floor and top spikes raise the speaker enclosure from the stand ensuring the cleanest possible sound. 450mm high. 180x180mm speaker base plate.

Base plate is adjustable from 165mm to 300mm, front to back. Suitable for speakers up to 10kg in weight. The bracket can be angled 20° vertically and 180° horizontally. Perfect for mounting bookshelf or surround sound speakers.
Supplied in pairs.

M6 to 1/4" male Wacki® bracket adaptor.

Heavy duty wall mount bracket designed for 35mm diameter 'top hat' mounts as found in professional audio loudspeakers. Suitable for speakers up to 40kg in weight. The bracket can be angled 20° vertically and 180° horizontally.

A Hardware pack to enable the mounting of the H 8040 Maxi mount series of brackets.
Suitable for gyprock or plaster fixing.

A Hardware pack to enable the mounting of the H 8040 Maxi mount series of brackets.
Suitable for timber frame fixing.

A Hardware pack to enable the mounting of the H 8040 Maxi mount series of brackets.
Suitable for masonary fixing.

This unique heavy duty swivel bracket will hold loads up to 15kg.
The two piece construction makes it a breeze to install large heavy speaker boxes for example. Installation is simple. The base is fixed to the wall, the swivel assembly is then fixed to the speaker box and set to the desired angle. The box with swivel assembly is then slotted into the base and snap-locked into position. Minor angle adjustments can then be made. Provision has been made for a security screw to prevent theft. Ideal for mounting speakers, security lights, CCTV cameras etc. The unique design allows up to approx. 50° angle variation either vertically or horizontally.

Features:

• Up to 50° angle variation • Requires no special tools for installation • Installs in minutes • Payload of up to 15 kgs • Available in White or Black • Australian designed and manufactured

This unique heavy duty swivel bracket will hold loads up to 15kg. The two piece construction makes it a breeze to install large heavy speaker boxes for example. Installation is simple. The base is fixed to the wall, the swivel assembly is then fixed to the speaker box and set to the desired angle. The box with swivel assembly is then slotted into the base and snap-locked into position. Minor angle adjustments can then be made. Provision has been made for a security screw to prevent theft. Ideal for mounting speakers, security lights, CCTV cameras etc. The unique design allows up to approx. 50° angle variation either vertically or horizontally.

Features:

Up to 50° angle variation Requires no special tools for installation Installs in minutes Payload of up to 12 kgs Available in White or Black Australian designed and manufactured

M6 to M6 angled extension rod 100mm.

Enables the Wacki Bracket to use a H 8028 angled extension rod.
M6 to M6 female ferrule.

Enables the Wacki Bracket to mate to M5.
M6 to M5 female ferrule.

Enables the Wacki Bracket to mate to M4.
M6 to M4 female ferrule.

Wacki® Angled mounting option; For installations requiring additional angle of adjustment. 35° bend. Black.

Wacki® Angled mounting option; For installations requiring additional angle of adjustment. 35° bend. White.