(SC May 2008) If the CDI module in your motorbike, outboard, ride-on mower or other small petrol motor fails, you could be in for a shock. Depending on the brand or model, they can cost up to $400. You can build this one for less than $30 and it will do the same job for most engines. Please note that this kit will not replace units that generate their own high voltage from an inverter requiring a 12V battery supply.

(ETI September ’80) Brilliant single chip design by ETI. Ten segment display indicates exact voltage in 0.5V increments from 10.5V to 15V.

Features

• Invaluable where voltage monitoring is essential, i.e. battery charging circuit • Great as a car battery voltmeter to allow you to diagnose an electrical problem • Ideal as a deep-cycle battery monitor for inverter applications.

Dimensions

70 x 40 x 30 mm

(SC Jan ’92) Build this simple little device, and avoid getting caught out with a flat battery during your holidays. It simply connects into a 12V accessories power line, and shuts off the flow if the battery voltage drops to a dangerously low level. Ideal for battery powered camping fridges etc.

Adjustable cutout variable from 10.9V to 11.9V. Includes automatic or manual voltage reset function.

(EA Aug ’99) This project automatically switches on your cars headlights during the day, making your vehicle more visible to other vehicles on the road. It drives the low beam circuit of your vehicle at 80% brightness during the day and will automatically switch to full brightness in low light or darkness.

Features

• Headlights Automatically switch on/off with ignition. • Handles up to 200W of headlights. • EMI suppressed • Darkness sensor to switch light to full brightness automatically. • High beam circuit is unaffected.

(SC Nov ‘98) Turbo charged engines must be run at idle for a few minutes to cool down after a long journey to avoid damage. This project allows your car to be run for a few minutes at idle speed so you can lock the car and leave it to turn off by itself.

Features

• 90 second time-out • Under temp. disable • Reset switch • Robust flanged box • Simulated Ignition cutout for immobiliser • No battery power drain once shutdown

(SC Jan '99) Monitoring the charging behaviour of your battery can be advantageous in finding a fault with the ignition of your car or perhaps preventing the fault from occurring through early detection. This project monitors the negative strap across the battery to provide accurate information on the charge and discharge behaviour of your battery.

Features

• Suitable for any 12V system • No need to alter existing ignition wiring • Measures up to 25A charge & 25A discharge in 5A LED steps • Supplied with an attractive automotive style housing.

The gear indicator kit does just that, indicates what gear you are in on a digital display readout. Perfect for auto's, manuals, and motorbikes to ensure you are always selecting the right gear at the right time for the right situation without drawing your attention too far away from the road.

Features:

• Indicates up to 9 gears • Neutral indication. • Reverse indication. • Easy gear calibration. • Adjustable parameters. • Adjustable reverse gear switch level. • Display Dimming."

This kit will monitor the fuel mixture of an unleaded engine in real time. Displaying both the fuel/air ratios via the digital display and rich to lean mixture via the LED bargraph.

Features

• Suits vehicles with zirconia EGO probes • Compact • Dot or Bar mode option for bargraph • Air-Fuel ratio matched for Bosch LSM11 (0258104002) EGO probe • Suitable for petrol , LPG or propane • Automatic display dimming • 0-1V display for setting up adjustments

(SC August ’01) Ever had a flat battery in your car from leaving your lights on? The K 4348 can help by sounding an alarm when you open the door if you have left the headlights on.

Features

• Connects easily to existing wiring • Works only when engine is off • Alarm time out • Monitors doors and ignition

(SC August ‘03) Convert your analog instruments into hi tech digital ones. This project is
ideal for use as a fuel, oil pressure or temperature gauge. Suitable for connection to variable resistance or voltage sensors.

Features

• Suitable for use with a variety of sensors • Suits fuel level, oil pressure, engine temperature, intake temperature etc. • Programmable alarm level • Alarm buzzer output • Auto dimming at night time • Visual alarm output • 2 second display update period

(EA Jan ‘99) A very simple, yet extraordinarily effective deterrent to car thieving persons. Controlled by a hidden switch inside your car, this alarm will sound an ear-piercing 110dB piezo siren inside your vehicle when tripped, making life very uncomfortable for anyone there! Features exit and entry delay, with a soft three second pre-warn in case you forget to deactivate it, a super bright LED warning lamp and two trigger inputs. A budget alternative to commercial car alarms! Dimensions: 57 x 93 x 20 mm

(SC Dec ‘08) A do-it-all digital readout for your car’s dashboard. Monitors up to six signals and displays up to 10 computed values in a scrolling or static readout. Measure values such as fuel injector duty cycle, air/fuel ratio, cabin/engine temp, fuel tank level, battery voltage etc or a plethora of car ECU signals. Board dimensions: 134 x 86mm.

Main Features and Specs:

- Can be powered from 9-12V DC or from a USB port (5V). - Two Frequency/Duty Cycle Inputs with frequency up to 10kHz. - Positive Duty Cycle Range: 0-100%. - Four Voltage/Resistance Inputs Plus Battery Voltage (the latter has its own channel). - Voltage Range: 0-16V (greater or smaller ranges possible by changing one resistor). - Sensitivity with 16V scale: approx. 16mV. - Best Sensitivity: approx. 5mV (requires changing one resistor and recalibrating using the supplied PC software). - Two output channels to drive external relays or buzzers. - Up to 10 displayed variables. - Averaging or direct acquisition mode for each variable. - Screen dimming on ambient light with adjustable sensitivity and selectable minimum brightness. - 7 x 15 dot matrix LED display (scrolling or static display). - Static display of up to 4 digits (floating point) - Selectable scrolling speed. - On screen limit warnings for each variable in the static display mode. - Software calibration using polynomial interpolation. - Persistent settings stored in non-volatile memory. - Easily load and store previous settings to file on your computer. - Easily load and store different calibration point files on your computer. - All settings changeable using the USB port and PC host program. - Data logging via the USB port; selectable variable update frequency from 0.1-8Hz; can collect 1000s of samples to a PC’s hard drive.

(SC October ’01) This kit operates from 12VDC so is perfect for the car or home. It displays both inside and outside temperature at the push of a button via the digital display.

 

Features

• PIC microprocessor controlled • -40° to 125° C range • Accuracy better than 1 percent • Display dimming at night • Fits inside the smallest jiffy box"

(SC March ‘03)
This simple circuit can be used as a stand alone unit or in conjunction with other kits such as the K 5360 portable P.A. Unlike similar designs this unit feeds your batteries with pure DC and automatically disconnects the battery when power is removed from the charger. It will charge a 7.2aH battery ito full capacity in 14 hours.

Features

• Pure DC output • Relay disconnect at power off • Up to 7.2aH charging capacity • 16VAC operation

(SC July ‘89) These simple circuits will recharge your 6 or 12V Gell Cells correctly, considerably increasing their life span. Kit consists of one IC and a handful of external components plus the PCB. Charging current and voltage is controlled and over-charging is avoided by the IC switching off when the cell is fully charged

Features

• Supplied with components to build either 6V or 12V version • Automatic charge rate • Extends life of Gell Cells • 12V input 15 to 24V DC • 6V input 9 to 24V DC • Simple to construct • Supplied with chip details to allow experimentation & expansion of this kit • Dedicated IC

(SC Nov/Dec ’99) The best way to reduce the number of speeding fines you receive each year is to simply avoid speeding! This kit lets you know when you’re speeding by emitting an alarm and flashing a dashboard LED. The alarm point is adjustable in increments of 5 kph from 0 to 155 kph. It'll tell you when you're speeding without taking your eyes off the road. A single trimpot is used to calibrate the unit to your existing speedometer. Kit comes complete with screened & punched case. Suits front and rear-wheel drive vehicles.

Features

• Display brightness automatically adjusts to light conditions • Automatic calibration • Visible and audible alarm when preset speed is exceeded • Unit can display alarm speed or vehicle speed • Supplied with pre- punched and screened front panel • Compact 83 x 54 x 30mm

(SC April ‘08) Works in tandem with a power supply or standard battery charger to provide staged float charging for sealed & non-sealed lead acid batteries. This prolongs battery life and prevents overcharging damage that cheap battery chargers can cause. It includes temperature compensation and LED indication. All parameters are adjustable for charging leadacid or Sealed Lead Acid (SLA) batteries.

SHORT FORM KIT - PCB's & COMPONENTS ONLY

(SC November ’04) Deep cycle batteries must be correctly charged to deliver full capacity and extended service life. A general purpose 12V car battery charger is generally not suitable. This 3 step deep cycle charger will charge to a maximum of 16.6A when used with the M 5518 transformer. This is a 3 PCB short form kit and does not contain case, transformer, heatsink, wire, fan, thermocouples etc. Refer to internet for full parts lists.

When fully constructed, it features:

LCD readout
Temperature, current & voltage metering
4 preset battery chemistry settings
Correction for voltage drop across battery leads
3 step charging to suit deep cycle batteries

Please consult the parts list in the downloads section for full information on what components are included with this kit. A list is also provided showing what additional parts are required to complete the charger.

(SC September 07) A truly versatile charger capable of charging up to 15 identical NiMH or NiCad cells. Built it to suit any size cells or capacity. It features an adjustable fast charge rate plus trickle charging. Temperature sensing in built prevents overcharging of cells.

Case to suit H 0432.

Heatsink to suit H 0520.

A valuable teaching aid developed by the Edinburgh University. This pack includes four ‘see-through’ IC’s mounted on a prototyping board, plus a comprehensive booklet which outlines in simple language how different IC’s operate. Several practical lessons are provided which teach students about resistor networks, transistor MOSFETS, optoelectronics, oscillators and more. A great way to learn about integrated circuits!

Features

• A superb teaching aid for electronics classrooms • See through casings allow closeup inspection of IC internals • Includes magnifier, booklet, IC’s and board • University developed

(SC July ‘08) The high tech version of a tuning fork. Produces any note of the tempered musical scale at a standard pitch (A = 440.00Hz) and spans the 8 commonly used octaves. Allows easy tuning for just about any instrument, acoustic or electronic. High accuracy of ±0.08% (or 1.3 musical cents), ensures your instrument need never be out of tune again! 9V battery powered plus plugpack input.

Features:

• Spans 8 octaves • Produces any note on the musical scale for tone/pitch matching • 8 LED stroboscopic beat indicator

This simple FM Microphone Kit can be built in next to no time and only requires an ordinary FM Radio for reception. Works in the standard FM Range 88-108MHz (adjustable). Runs from a single 9V battery. High sensitivity microphone insert supplied. Transmission range is approximately 30M in ideal conditions.

Uses

• Wireless Microphone • Listen to the TV in the kitchen • Could be adapted to an alarm eg. send a tone to your clock radio when your car alarm trips etc. etc.

This robotic bug kit is a fun and educational introduction to electronics. It uses three infra red emitting diodes to navigate its way around objects, through mazes etc. The inbuilt microprocessor enables it to 'think' on its own as it processes information about the environment around it. Kit comes supplied with all components required to build a fully working robotic bug as well as two sets of legs for different movements. Requires 4 x AAA batteries (not included).

This robotic base provides an excellent foundation for your own robot design. It contains 2 motors and all necessary parts required for your robots gearbox. Wheels and feet are provided depending on how you want your robot to get around! Simple comprehensive instructions are provided so just about anyone can build it. Great for custom PICAXE or Atmel designs. Perfect for enthusiasts, designers, inventors and students.

(Designed by Labtronics) LED Fun is a PIC - based multi-function kit which uses a small micro controller to activate LED's and a buzzer. The kit can be configured to one of 8 different LED based projects ranging from an electronic dice to a LED chaser. Great for beginners or as an introductory class project.

FREE CoreChart and ezCircuit Lite Software!

An educational introduction to robot building, electronics and microcontrollers. The kit is easily assembled by students or beginners with basic soldering skills. The re-programmable PIC16F819 eRacer follows lines and avoids objects ( LDR & IR sensors ). Two independent motors power the eRacer around. The included USB programmer unit allows enthusiasts to create their own tasks and behaviour for the eRacer. All components, chassis parts and wheels are provided.

Great for students or robot enthusiasts! Requires 4 x AA batteries.

CoreChart is a "drag and drop" industry strength assembler software for programming microcontrollers. Designed for use with the K 1099 eRacer, the K 9505 programmer and most PIC
programmers. It produces asm and hex files directly, ready to download to the micro in one simple step! The user literally paints their program using icons instead of typing it at a keyboard.
Suitable for all ages, it is used by thousands of high school students in the CoreChart Robotics Peer Mentoring program. CoreChart produces smaller and faster code which means it can run on
smaller, less costly chips. CoreChart supports PIC16F84A, PIC16F628, PIC16F819, PIC16F877, PIC16F877A, PIC12F629 and PIC12F675 chips.

Great fun for the kids! An educational electronics kit which, when constructed, is designed to track along black lines on a tabletop. Simply lay out a path of electrical tape, and watch it follow the path! It includes easy to follow instructions, and takes approximately 1 hour to assemble for the average child. Ages 4 and up. Requires 2 x AA batteries (not included).

Make your lounge room into a virtual battlefield as up to 4 tanks fight it out taking “virtual” potshots at eachother with infra red beams! This fantastic do-it-yourself kit comes with all the parts to
build a 6 wheel drive battle tank and controller (even camouflage stickers). Battle sounds make the experience complete! Its made to be easy enough for kids to build (ages 6 and up) and can be constructed in just an hour or two. Requires 4 x AAA & 4 x AA batteries.

A simple switchmode power supply module which is capable of powering up to two 1W/3W luxeon stars, or alternatively a single 5W luxeon star. The unique switchmode regulation employed means that it is very efficient and produces very little heat. Its 12V input makes it perfect for boats, cars, caravans. Anywhere low voltage lighting might be required.

The project can be powered from any 12V DC (nominal) supply and can be set up to source 350mA, 700mA or 1000mA of regulated current to suit all of the Luxeon Star LED range.

 

Features

Powers one or two 1W or 3W Stars, or a single 5W Star High efficiency for minimum battery drain Low battery cutout (11.5V) Input polarity & transient protected Output short-circuit protected Ideal for use in boats, caravans & car

To suit cables 7.4mm - 8.2mm. 1.9mm to 3.2mm chassis thickness. Hole size 15.9 x 14mm. Nylon type

To suit cables 7.4mm - 8.2mm. 1.9mm to 3.2mm chassis thickness. Hole size 15.9 x 14mm. Nylon type

To suit cables 7.4mm - 8.2mm. 1.9mm to 3.2mm chassis thickness. Hole size 15.9 x 14mm. Nylon type

To suit cables 7.4mm - 8.2mm. 1.9mm to 3.2mm chassis thickness. Hole size 15.9 x 14mm. Nylon type. Pack 1000

To suit cables 7.4mm - 8.2mm. 1.9mm to 3.2mm chassis thickness. Hole size 15.9 x 14mm. Nylon type. Pack 100

To suit cables 7.4mm - 8.2mm. 1.9mm to 3.2mm chassis thickness. Hole size 15.9 x 14mm. Nylon type. Pack 10

To suit cables 7.4 - 8.2mm. 0.5mm to 1.6mm chassis thickness. Hole size 15.9 x 14mm. Nylon type. Pack 1000

To suit cables 7.4 - 8.2mm. 0.5mm to 1.6mm chassis thickness. Hole size 15.9 x 14mm. Nylon type. Pack 100

To suit cables 7.4 - 8.2mm. 0.5mm to 1.6mm chassis thickness. Hole size 15.9 x 14mm. Nylon type. Pack 10

To suit cables 6.2 - 7.4mm. 1.8mm to 2.5mm chassis thickness. Hole size 12.7 x 11.5mm. Nylon 66, 94V-2. Pack 1000

To suit cables 6.2 - 7.4mm. 1.8mm to 2.5mm chassis thickness. Hole size 12.7 x 11.5mm. Nylon 66, 94V-2. Pack 100

To suit cables 6.2 - 7.4mm. 1.8mm to 2.5mm chassis thickness. Hole size 12.7 x 11.5mm. Nylon 66, 94V-2. Pack 10

This customisable rack case allows vertical or horizontal mounting of sub-chassis’ within the case. PCB’s and modules can be easily mounted along the full length and height of the case to the 4 racking strips or to the internal sub chassis panel provided. These allow vertical or horizontal mounting. The black anodised aluminium front & rear panels are easily machined making these cases well suited for manufacturers.

Dimensions: 430W x 330D.

Features:

• Aluminium powdercoated rear panel • Steel powdercoated top, bottom & side panels. • 19” rack mountable • Internal strips adjustable along the entire height and length of the case • 4 strips provided • Metal carry handles • Internal separation panel provided • Stylish aluminium anodised black front panel

This customisable rack case allows vertical or horizontal mounting of sub-chassis’ within the case. PCB’s and modules can be easily mounted along the full length and height of the case to the 4 racking strips or to the internal sub chassis panel provided. These allow vertical or horizontal mounting. The black anodised aluminium front & rear panels are easily machined making these cases well suited for manufacturers.

Dimensions: 430W x 330D.

Features:

• Aluminium powdercoated rear panel • Steel powdercoated top, bottom & side panels. • 19” rack mountable • Internal strips adjustable along the entire height and length of the case • 4 strips provided • Metal carry handles • Internal separation panel provided • Stylish aluminium anodised black front panel

Vented type. This version has provision for front rocker switch and rear IEC power socket.

Specifically designed for high output equipment. Optional rack mounting ears.

Features

Vented on lid, base and sides. Heatsink mounting points (Suits H 0552) Aluminium gloss powdercoated front and rear panels 19" Rack Mountable (when fitted with ears) Sleet matt finish powdercoated side / top / bottom panels Supplied in flat pack format, assembles in minutes

Dimensions

420W x 360D x 88H (minus rack ears)

Non-vented type. Note: This type does not have provision for front switch or rear IEC socket (see H 5047)

Specifically designed for high output equipment. Optional rack mounting ears.

Features

Aluminium gloss powdercoated front and rear panels 19" Rack Mountable (when fitted with ears) Sleet matt finish powdercoated side / top / bottom panels Supplied in flat pack format, assembles in minutes

Dimensions

420W x 360D x 88H (minus rack ears)

2 Unit vented panel for improving rack ventilation around hot equipment. Powdercoated black.

1 unit (44mm) high. Ideal for any 19" rack system which requires additional airflow to help keep equipment cool.

Simply bolts onto the front of your rack equipment to provide protection from accidental adjustments. Available in 1U and 2U sizes. 19mm depth allows most knobs and switches to fit behind.

Simply bolts onto the front of your rack equipment to provide protection from accidental adjustments. Available in 1U and 2U sizes. 19mm depth allows most knobs and switches to fit behind.

Manufactured from 1mm steel and finished in a textured powdercoat. Bevelled edges match Redback audio equipment.

Manufactured from 1mm steel and finished in a textured powder coat. The top and bottom edges of each panel have a return for added rigidity.

Manufactured from 1mm steel and finished in a textured powder coat. The top and bottom edges of each panel have a return for added rigidity.

Manufactured from 1mm steel and finished in a textured powder coat. The top and bottom edges of each panel have a return for added rigidity.

Manufactured from 1mm steel and finished in a textured powder coat. The top and bottom edges of each panel have a return for added rigidity.

Manufactured from 1mm steel and finished in a textured powder coat. The top and bottom edges of each panel have a return for added rigidity.

Ideal for professional looking custom switch panels, control panels or to fill in blank spaces in rack frames.
All models feature integral ribs on the rear for extra strength and rigidity.

Ideal for professional looking custom switch panels, control panels or to fill in blank spaces of rack frames. All models feature integral ribs on the rear for extra strength and rigidity of the panel.

Ideal for professional looking custom switch panels, control panels or to fill in blank spaces of rack frames. All models feature integral ribs on the rear for extra strength and rigidity of the panel.

Ideal for professional looking custom switch panels, control panels or to fill in blank spaces of rack frames. All models feature integral ribs on the rear for extra strength and rigidity of the panel.

Ideal for professional looking custom switch panels, control panels or to fill in blank spaces of rack frames. All models feature integral ribs on the rear for extra strength and rigidity of the panel.

Ideal for professional looking custom switch panels, control panels or to fill in blank spaces of rack frames. All models feature integral ribs on the rear for extra strength and rigidity of the panel.

All new modern design featuring a recessed bevelled front panel gives these rack cases a very professional appearance. The front panel is constructed from 1.2mm and the rear panel is constructed from 1.5mm aluminium making them very easy to machine. The one piece side panel rack ear combination is manufactured from 2mm steel ensuring a very sturdy construction.

Features:

• Black textured powdercoat finish • Aluminium & steel construction with removable top and bottom panels • All dimensions conform to the International Standard • Ventilated lid • Deluxe finish front panel • Available in either 1U or 2U size

All new modern design featuring a recessed bevelled front panel gives these rack cases a very professional appearance. The front panel is constructed from 1.2mm and the rear panel is constructed from 1.5mm aluminium making them very easy to machine. The one piece side panel rack ear combination is manufactured from 2mm steel ensuring a very sturdy construction.

Features:

• Black textured powdercoat finish • Aluminium & steel construction with removable top and bottom panels • All dimensions conform to the International Standard • Ventilated lid • Deluxe finish front panel • Available in either 1U or 2U size

Features:

• Raw aluminium or black anodised front panel • 1.5mm aluminium rear panel for easy machining • Steel sides and removable top and bottom steel panels • All dimensions conform to the International Standard • Ventilated lid • Deluxe finish front panel • Individually packaged • Supplied in flat pack form - Easily assembled in minutes

Dimensions

Each finish is available in 1U (44mm), 2U (88mm) or 3U (132mm) high. Overall depth 255mm. Mounting hole centres conform exactly to international racking specifications both vertically and horizontally.

Features:

• Raw aluminium or black anodised front panel • 1.5mm aluminium rear panel for easy machining • Steel sides and removable top and bottom steel panels • All dimensions conform to the International Standard • Ventilated lid • Deluxe finish front panel • Individually packaged • Supplied in flat pack form - Easily assembled in minutes

Dimensions

Each finish is available in 1U (44mm), 2U (88mm) or 3U (132mm) high. Overall depth 255mm. Mounting hole centres conform exactly to international racking specifications both vertically and horizontally.

Features:

• Raw aluminium or black anodised front panel • 1.5mm aluminium rear panel for easy machining • Steel sides and removable top and bottom steel panels • All dimensions conform to the International Standard • Ventilated lid • Deluxe finish front panel • Individually packaged • Supplied in flat pack form - Easily assembled in minutes

Dimensions

Each finish is available in 1U (44mm), 2U (88mm) or 3U (132mm) high. Overall depth 255mm. Mounting hole centres conform exactly to international racking specifications both vertically and horizontally.

Features

• Raw aluminium or black anodised front panel • 1.5mm aluminium rear panel for easy machining • Steel sides and removable top and bottom steel panels • All dimensions conform to the International Standard • Ventilated lid • Deluxe finish front panel • Individually packaged • Supplied in flat pack form - Easily assembled in minutes

Dimensions

Each finish is available in 1U (44mm), 2U (88mm) or 3U (132mm) high. Overall depth 255mm. Mounting hole centres conform exactly to international racking specifications both vertically and horizontally.

Features

• Raw aluminium or black anodised front panel • 1.5mm aluminium rear panel for easy machining • Steel sides and removable top and bottom steel panels • All dimensions conform to the International Standard • Ventilated lid • Deluxe finish front panel • Individually packaged • Supplied in flat pack form - Easily assembled in minutes

Dimensions

Each finish is available in 1U (44mm), 2U (88mm) or 3U (132mm) high. Overall depth 255mm. Mounting hole centres conform exactly to international racking specifications both vertically and horizontally.

Vented panel, specifically designed to add rigidity to our rack frames. Pre-drilled with extra mounting holes to install into the top and bottom of the rack frames. Tough powdercoated finish.

Blanking panel for H 5171 and H5173
Pk. 6

Blanking panel for H 5170 and H5172
Pk. 6

Pre-punched with either 12(1U) or 24(2U). Tough black powdercoated finish. H 5171 & H 5173 suits our range of plastic XLR connectors.

Pre-punched with either 12(1U) or 24(2U) 26mmø Holes at 31mm Diagonal Mounting Centres. Tough black powdercoated finish.

Pre-punched with either 12(1U) or 24(2U). Tough black powdercoated finish. H 5171 & H 5173 suits our range of
plastic XLR connectors.

Pre-punched with either 12(1U) or 24(2U) 26mmø Holes at 31mm Diagonal Mounting Centres. Tough black powdercoated finish.

These simple to install brackets provide rear or front support for equipment when installing into a rack. For instance when bolting a heavy amplifier into a rack, these brackets can hold the unit level allowing one person to easily bolt the amplifier into place.

2RU panel fitted with an 8 way powerboard with overload circuit breaker. The neat solution to supplying mains power to your rack mounted equipment. Simply screw this panel to your rack and plug equipment in.

Blanking plate powdercoated in the same colour as the main panel.
Supplied with hardware to suit.

Pre-punched with provision to suit 3 x 120mm fans. Tough powdercoated finish. Fans not supplied.

This recessed rack mounting gooseneck light is ideal for illuminating equipment within a rack. The flexible gooseneck enables the light to be directed where desired. It includes an inbuilt dimmer to adjust the light intensity.
Gooseneck length approx. 300mm.

Suits black 600mm deep series rack frames.
Raises rack by approximately 67mm.

Suits black series rack frames.
Raises rack by approximately 67mm.

Includes 2 free wheeling and 2 with locking mechanisms. Suits all rack frames.

All models supplied in flat pack form which assemble in minutes. All models feature tough black powdercoat finish. Simply screws to the wall. Suitable for C.D. players, tuners, videos, computer monitors.

All models supplied in flat pack form which assemble in minutes. All models feature tough black powdercoat finish. Simply screws to the wall. Suitable for C.D. players, tuners, videos, computer monitors.

All models supplied in flat pack form - assembles in minutes. Simply screws to the rack frame. Suitable for equipment that does not rack mount, e.g. C.D. players, tuners, videos, computer monitors, etc.

All models supplied in flat pack form - assembles in minutes. Simply screws to the rack frame. Suitable for equipment that does not rack mount, e.g. C.D. players, tuners, videos, computer monitors, etc.

All models supplied in flat pack form - assembles in minutes. Simply screws to the rack frame. Suitable for equipment that does not rack mount, e.g. C.D. players, tuners, videos, computer monitors, etc.

All models supplied in flat pack form - assembles in minutes. Simply screws to the rack frame. Suitable for equipment that does not rack mount, e.g. C.D. players, tuners, videos, computer monitors, etc.

All models supplied in flat pack form - assembles in minutes. Simply screws to the rack frame. Suitable for equipment that does not rack mount, e.g. C.D. players, tuners, videos, computer monitors, etc.

All models supplied in flat pack form - assembles in minutes. Simply screws to the rack frame. Suitable for equipment that does not rack mount, e.g. C.D. players, tuners, videos, computer monitors, etc.

This sliding shelf is ideal for mounting equipment that needs to be readily accessible for service or configuration. ie. Keyboard. Tough powdercoated finish. Accommodates equipment up to 120mm high.

All models supplied in flat pack form - assembles in minutes. Simply screws to the rack frame. Suitable for equipment that does not rack mount, e.g. C.D. players, tuners, videos, computer monitors, etc. Includes rack ears front and back to allow fixing to both the front and rear of the rack for maximum support.

This lockable sliding drawer is ideal for holding any patch leads, connectors, tools, etc within a rack frame. It could also be used to house CDs, tapes, microphones, spare parts, etc. Tough powdercoated finish. Internal dimensions 415L x 415W x 120Hmm.

All models supplied in flat pack form - assembles in minutes. Simply screws to the rack frame. Suitable for equipment that does not rack mount, e.g. C.D. players, tuners, videos, computer monitors, etc. Includes rack ears front and back to allow fixing to both the front and rear of the rack for maximum support.

All models supplied in flat pack form - assembles in minutes. Simply screws to the rack frame. Suitable for equipment that does not rack mount, e.g. C.D. players, tuners, videos, computer monitors, etc.

Extra deep model for use in 600mm deep rack frames.

All models supplied in flat pack form - assembles in minutes. Simply screws to the rack frame. Suitable for equipment that does not rack mount, e.g. C.D. players, tuners, videos, computer monitors, etc.

Extra deep model for use in 600mm deep rack frames.

All models supplied in flat pack form - assembles in minutes. Simply screws to the rack frame. Suitable for equipment that does not rack mount, e.g. C.D. players, tuners, videos, computer monitors, etc.

Extra deep model for use in 600mm deep rack frames.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, 450mm deep for audio equipment or 600mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in Black to match most equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.

Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.

Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, 450mm deep for audio equipment or 600mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in Black to match most equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.

Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.

Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, 450mm deep for audio equipment or 600mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in Black to match most equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.

Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.

Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, 450mm deep for audio equipment or 600mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in Black to match most equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.

Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.

Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, 450mm deep for audio equipment or 600mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in Black to match most equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.

Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.

Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, 450mm deep for audio equipment or 600mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in Black to match most equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.

Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.

Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, 450mm deep for audio equipment or 600mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in Black to match most equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.

Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.

Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, 450mm deep for audio equipment or 600mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in Black to match most equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.

Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.

Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, 450mm deep for audio equipment or 600mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in Black to match most equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.

Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.

Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, 450mm deep for audio equipment or 600mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in Black to match most equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.

Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.

Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, 450mm deep for audio equipment or 600mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in Black to match most equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.

Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.

Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, 450mm deep for audio equipment or 600mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in Black to match most equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.

Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.

Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audio equipment or sandstone 700mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in either Sandstone or Black to match most modern computer and audio equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.
Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.
Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

*Picture for illustration purposes only. Rack sold separately.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audio equipment or sandstone 700mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in either Sandstone or Black to match most modern computer and audio equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.
Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.
Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

*Picture for illustration purposes only. Rack sold separately.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audio equipment or sandstone 700mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in either Sandstone or Black to match most modern computer and audio equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.
Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.
Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

*Picture for illustration purposes only. Rack sold separately.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, 450mm deep for audio equipment or 600mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in Black to match most equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.

Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.

Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, 450mm deep for audio equipment or 600mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in Black to match most equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.

Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.

Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, 450mm deep for audio equipment or 600mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in Black to match most equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.

Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.

Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, 450mm deep for audio equipment or 600mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in Black to match most equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.

Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.

Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audio equipment or sandstone 700mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in either Sandstone or Black to match most modern computer and audio equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.
Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.
Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

*Picture for illustration purposes only. Rack sold separately.

These cable trays bolt to one of the upright sections in a rack frame and allow equipment leads to be cable tied neatly to the tray. This reduces the stress on the leads and also the risk of equipment becoming disconnected accidentally. Suits rack frames from 12U to 38U.

These cable trays bolt to one of the upright sections in a rack frame and allow equipment leads to be cable tied neatly to the tray. This reduces the stress on the leads and also the risk of equipment becoming disconnected accidentally. Suits rack frames from 12U to 38U.

These cable trays bolt to one of the upright sections in a rack frame and allow equipment leads to be cable tied neatly to the tray. This reduces the stress on the leads and also the risk of equipment becoming disconnected accidentally. Suits rack frames from 12U to 38U.

These cable trays bolt to one of the upright sections in a rack frame and allow equipment leads to be cable tied neatly to the tray. This reduces the stress on the leads and also the risk of equipment becoming disconnected accidentally. Suits rack frames from 12U to 38U.

These cable trays bolt to one of the upright sections in a rack frame and allow equipment leads to be cable tied neatly to the tray. This reduces the stress on the leads and also the risk of equipment becoming disconnected accidentally. Suits rack frames from 12U to 38U.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, 450mm deep for audio equipment or 600mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in Black to match most equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.

Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.

Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, 450mm deep for audio equipment or 600mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in Black to match most equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.

Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.

Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

These cable trays bolt to one of the upright sections in a rack frame and allow equipment leads to be cable tied neatly to the tray. This reduces the stress on the leads and also the risk of equipment becoming disconnected accidentally. Suits rack frames from 12U to 38U.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audio equipment or sandstone 700mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in either Sandstone or Black to match most modern computer and audio equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.
Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.
Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

*Picture for illustration purposes only. Rack sold separately.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, 450mm deep for audio equipment or 600mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in Black to match most equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.

Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.

Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

Turn your custom cabinet into a rack cabinet. Ideal for use in road cases or custom timber cabinets. Sold as a pair.

Turn your custom cabinet into a rack cabinet. Ideal for use in road cases or custom timber cabinets. Sold as a pair.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, 450mm deep for audio equipment or 600mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in Black to match most equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.

Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.

Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audio equipment or sandstone 700mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in either Sandstone or Black to match most modern computer and audio equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.
Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.
Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

*Picture for illustration purposes only. Rack sold separately.

A vented steel panel designed to suit the range of 600mm rack frames. It is louvered to allow heat to flow up and away from the cabinet but reduce the amount of dust and dirt collected on top of the equipment within the rack.

A vented steel panel designed to suit the range of Black rack frames. It is louvered to allow heat to flow up and away from the cabinet but reduce the amount of dust and dirt collected on top of the equipment within the rack.

A top of bottom panel to suit 600mm rack frames. Powdercoated black.

A top of bottom panel to suit Black 450mm rack frames. Powdercoated black.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, 450mm deep for audio equipment or 600mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in Black to match most equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.

Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.

Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audio equipment or sandstone 700mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in either Sandstone or Black to match most modern computer and audio equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.
Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.
Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

*Picture for illustration purposes only. Rack sold separately.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, 450mm deep for audio equipment or 600mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in Black to match most equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.

Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.

Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audio equipment or sandstone 700mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in either Sandstone or Black to match most modern computer and audio equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.
Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.
Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

*Picture for illustration purposes only. Rack sold separately.

Allows a rack frame to be wall mounted. Features cable entry in bottom and back panel for easy installation. Suitable for ~90kg loads with adequate fixings. Supplied in flat pack format

Overall Size: 555W x 455D x 275H mm

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audio equipment or sandstone 700mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in either Sandstone or Black to match most modern computer and audio equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.
Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.
Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

*Picture for illustration purposes only. Rack sold separately.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audio equipment or sandstone 700mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in either Sandstone or Black to match most modern computer and audio equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.
Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.
Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

*Picture for illustration purposes only. Rack sold separately.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audio equipment or sandstone 700mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in either Sandstone or Black to match most modern computer and audio equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.
Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.
Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

*Picture for illustration purposes only. Rack sold separately.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audio equipment or sandstone 700mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in either Sandstone or Black to match most modern computer and audio equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.
Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.
Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

*Picture for illustration purposes only. Rack sold separately.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audio equipment or sandstone 700mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in either Sandstone or Black to match most modern computer and audio equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.
Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.
Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

*Picture for illustration purposes only. Rack sold separately.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audio equipment or sandstone 700mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in either Sandstone or Black to match most modern computer and audio equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.
Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.
Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

*Picture for illustration purposes only. Rack sold separately.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audio equipment or sandstone 700mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in either Sandstone or Black to match most modern computer and audio equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.
Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.
Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

*Picture for illustration purposes only. Rack sold separately.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audio equipment or sandstone 700mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in either Sandstone or Black to match most modern computer and audio equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.
Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.
Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

*Picture for illustration purposes only. Rack sold separately.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audio equipment or sandstone 700mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in either Sandstone or Black to match most modern computer and audio equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.
Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.
Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

*Picture for illustration purposes only. Rack sold separately.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audio equipment or sandstone 700mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in either Sandstone or Black to match most modern computer and audio equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.
Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.
Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

*Picture for illustration purposes only. Rack sold separately.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audio equipment or sandstone 700mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in either Sandstone or Black to match most modern computer and audio equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.
Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.
Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

*Picture for illustration purposes only. Rack sold separately.  

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audio equipment or sandstone 700mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in either Sandstone or Black to match most modern computer and audio equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.
Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.
Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

*Picture for illustration purposes only. Rack sold separately.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audio equipment or sandstone 700mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in either Sandstone or Black to match most modern computer and audio equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.
Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.
Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

*Picture for illustration purposes only. Rack sold separately.

These racking systems have been designed for audio and communication systems. They are durable, strong , good looking, lightweight, easy to assemble and suit the modern day office environment. There are two series to choose from, black 450mm deep for audio equipment or sandstone 700mm extra deep for communication and computer equipment.

Rack frames: These extruded aluminium rack frames are finished in either Sandstone or Black to match most modern computer and audio equipment. Equipment can be mounted from the front or rear as all uprights are fully punched. Matching panel sets are also available separately (Comprising of 2 sides & a top panel). Provision has been made for optional castors to simply snap-fit if required. This makes it very simple to move the rack.
Rack Frame Doors: Matching doors are available constructed from folded steel with or without a clear perspex panel. All models are provided with two key locks except the 9U models which are provided with a single key lock.
Assembly: Each rack frame is supplied complete with 12 custom extruded aluminium sections and 8 ABS corner connector pieces. The sections and corner pieces simply push-fit together. A rubber or wooden mallet is recommended to fit together the self aligning pieces. Further strength can be obtained by pop rivetting the various overlapping extruded sections if desired. Rack doors are fixed to the rack frame by using pop rivets or screws. Installation of the handles and locks is a simple procedure and installation instructions are supplied.

*Picture for illustration purposes only. Rack sold separately.

M6 x 16mm black
Pack Qty: 1000

M6 x 16mm black
Pack Qty: 100

M6 x 16mm black
Pack Qty: 12

M6 x 16mm zinc plated
Pack Qty: 1000

M6 x 16mm zinc plated
Pack Qty: 100

M6 x 16mm zinc plated
Pack Qty: 12

Nylon washer black suit M6
Pack Qty: 1000

Nylon washer black suit M6
Pack Qty: 100

Nylon washer black suit M6
Pack Qty: 12

Nylon washer clear suit M6
Pack Qty: 1000

Nylon washer clear suit M6
Pack Qty: 100

Nylon washer clear suit M6
Pack Qty: 12

Captive nuts M6
Pack Qty: 100

Captive nuts M6
Pack Qty: 12

Captive nuts M6
Pack Qty: 1000

Wire Size

2x1.00mm

Colour

Yellow

Wire Size

2x1.00mm

Colour

Yellow

Wire Size

2x1.00mm

Colour

Yellow

Wire Size

2x0.75mm

Colour

Grey

Wire Size

2x0.75mm

Colour

Grey

Wire Size

2x0.75mm

Colour

Grey

Wire Size

2.5mm

Colour

Blue

Wire Size

2.5mm

Colour

Blue

Wire Size

2.5mm

Colour

Blue

Wire Size

1.5mm

Colour

Red

Wire Size

1.5mm

Colour

Red

Wire Size

1.5mm

Colour

Red

Wire Size

1.0mm

Colour

Yellow

Wire Size

1.0mm

Colour

Yellow

Wire Size

1.0mm

Colour

Yellow

Wire Size

0.75mm

Colour

White

Wire Size

0.75mm

Colour

White

Wire Size

0.75mm

Colour

White

Wire Size

0.5mm

Colour

Orange

Wire Size

0.5mm

Colour

Orange

Length: 8.0mm
Inner Diameter: 0.8mm
Outer Diameter: 1.1mm
Wire Size: 0.25mm

Length: 8.0mm
Inner Diameter: 0.8mm
Outer Diameter: 1.1mm
Wire Size: 0.25mm

Length: 8.0mm
Inner Diameter: 0.8mm
Outer Diameter: 1.1mm
Wire Size: 0.25mm

Soldered into PCB at assembly stage to provide test points for QA testing or repair. Single hole mount 0.8 - 1.0mm.

Soldered into PCB at assembly stage to provide test points for QA testing or repair. Single hole mount 0.8 - 1.0mm.

12mm height. Pack of 1000.

12mm height. Pack of 100.

12mm height. Pack of 8.

8mm height. Pack of 1000.

8mm height. Pack of 100.

8mm height. Pack of 8.

5mm height. Pack of 1000

Soldered into PCB at assembly stage to provide test points for QA testing or repair.
Single hole mount 0.8 - 1.0mm.

5mm height. Pack of 100

5mm height. Pack of 8.

Tapped to suit metric M3 machine Screws
Length: 25mm
Pack Qty: 1000

Tapped to suit metric M3 machine Screws
Length: 25mm
Pack Qty:100

Tapped to suit metric M3 machine Screws
Length: 25mm
Pack Qty:8

Tapped to suit metric M3 machine Screws
Length: 20mm
Pack Qty: 1000

Tapped to suit metric M3 machine Screws
Length: 15mm
Pack Qty: 100

Tapped to suit metric M3 machine Screws
Length: 15mm
Pack Qty: 8

Tapped to suit metric M3 machine Screws
Length: 15mm
Pack Qty: 1000

Tapped to suit metric M3 machine Screws
Length: 10mm
Pack Qty: 100

Tapped to suit metric M3 machine Screws
Length: 10mm
Pack Qty: 8

Chrome Plated Brass
Length: 25mm
Pack Qty: 1000

Chrome Plated Brass
Length: 25mm
Pack Qty: 100

Chrome Plated Brass
Length: 25mm
Pack Qty: 8

Chrome Plated Brass
Length: 12mm
Pack Qty: 1000

Chrome Plated Brass
Length: 12mm
Pack Qty: 100

Chrome Plated Brass
Length: 12mm
Pack Qty: 8

Chrome Plated Brass
Length: 9mm
Pack Qty: 1000

Chrome Plated Brass
Length: 9mm
Pack Qty:100

Chrome Plated Brass
Length: 9mm
Pack Qty: 8

Chrome Plated Brass
Length: 6mm
Pack Qty: 1000

Chrome Plated Brass
Length: 6mm
Pack Qty: 100

Chrome Plated Brass
Length: 6mm
Pack Qty: 8

3mm Clearance. All 5mm in diameter.
Length: 20mm
Pack Qty:1000

3mm Clearance. All 5mm in diameter.
Length: 20mm
Pack Qty: 100

3mm Clearance. All 5mm in diameter.
Length: 20mm
Pack Qty: 10

3mm Clearance. All 5mm in diameter.
Length: 15mm
Pack Qty: 1000

3mm Clearance. All 5mm in diameter.
Length: 15mm
Pack Qty: 100

3mm Clearance. All 5mm in diameter.
Length: 15mm
Pack Qty: 10

3mm Clearance. All 5mm in diameter.
Length: 12mm
Pack Qty: 1000

3mm Clearance. All 5mm in diameter.
Length: 12mm
Pack Qty: 100

3mm Clearance. All 5mm in diameter.
Length: 12mm
Pack Qty: 10

All nickel plated except shakeproof washers which are zinc plated.
Screw Pozi Dve Head M4 x 16
Pack Qty: 1000

All nickel plated except shakeproof washers which are zinc plated.
Screw Pozi Dve Head M4 x 16
Pack Qty: 200

All nickel plated except shakeproof washers which are zinc plated.
Screw Pozi Dve Head M4 x 16
Pack Qty: 25

All nickel plated except shakeproof washers which are zinc plated.
Screw Pozi Dve Head M4 x 10
Pack Qty: 1000

All nickel plated except shakeproof washers which are zinc plated.
Screw Pozi Dve Head M4 x 10
Pack Qty: 200

All nickel plated except shakeproof washers which are zinc plated.
Screw Pozi Dve Head M4 x 10
Pack Qty: 25

All nickel plated except shakeproof washers which are zinc plated.
Shakeproof Internal Tooth M4
Pack Qty:1000

All nickel plated except shakeproof washers which are zinc plated.
Shakeproof Internal Tooth M4
Pack Qty: 200

All nickel plated except shakeproof washers which are zinc plated.
Shakeproof Internal Tooth M4
Pack Qty: 25

All nickel plated except shakeproof washers which are zinc plated.
Flat M4
Pack Qty: 1000

All nickel plated except shakeproof washers which are zinc plated.
Flat M4
Pack Qty: 200

All nickel plated except shakeproof washers which are zinc plated.
Flat M4
Pack Qty: 25

All nickel plated except shakeproof washers which are zinc plated.
Nut M4 Hex
Pack Qty: 1000

All nickel plated except shakeproof washers which are zinc plated.
Nut M4 Hex
Pack Qty: 200

All nickel plated except shakeproof washers which are zinc plated.
Nut M4 Hex
Pack Qty: 25