Wall box to suit the A2339 attenuator. Allows the volume control to be mounted on the wall without excavating the wall.

VGA DE15 to RGB (3 x RCA) lead 3m.

Filtered DE15 High density male to male + 3.5mm audio

5m Lead

Filtered DE15 High density male to male

2m Lead

These 2 piece covers make it easy to identify your leads once installed in patch panels. Pk 100 Grey

These 2 piece covers make it easy to identify your leads once installed in patch panels. Pk 10 Grey

These 2 piece covers make it easy to identify your leads once installed in patch panels. Pk 100 Blue

These 2 piece covers make it easy to identify your leads once installed in patch panels. Pk 10 Blue

These 2 piece covers make it easy to identify your leads once installed in patch panels. Pk 100 Yellow

These 2 piece covers make it easy to identify your leads once installed in patch panels. Pk 10 Yellow

These 2 piece covers make it easy to identify your leads once installed in patch panels. Pk 100 Red

These 2 piece covers make it easy to identify your leads once installed in patch panels. Pk 10 Red

Allows non matching modular plugs and sockets to fit.

Allows non matching modular plugs and sockets to fit.

Specifications:

Housing: PBT Mixed 15% Glass Fibre, 94V-O Contact: Gold Plated Phosphor Bronze Alloy Insulation Resistance: 10M Ohm Minimum Contact Resistance: 20M Ohm Max. per contact Dielectric Withstand Voltage: 1000V AC RMS 60Hz Current Rating: 1.5 Amps Mechanical Life: 500 cycles minimum Retention Strength: 7.7kg between plug & socket

 

Specifications:

• Housing: PBT Mixed 15% Glass Fibre, 94V-O
• Contact: Gold Plated Phosphor Bronze Alloy
• Insulation Resistance: 10M Ohm Minimum
• Contact Resistance: 20M Ohm Max. per contact
• Dielectric Withstand Voltage: 1000V AC RMS 60Hz
• Current Rating: 1.5 Amps
• Mechanical Life: 500 cycles minimum
• Retention Strength: 7.7kg between plug &socket

*Specifications are subject to change without notice.

 

Specifications:

Housing: PBT Mixed 15% Glass Fibre, 94V-O Contact: Gold Plated Phosphor Bronze Alloy Insulation Resistance: 10M Ohm Minimum Contact Resistance: 20M Ohm Max. per contact Dielectric Withstand Voltage: 1000V AC RMS 60Hz Current Rating: 1.5 Amps Mechanical Life: 500 cycles minimum Retention Strength: 7.7kg between plug & socket

Specifications:

Housing: PBT Mixed 15% Glass Fibre, 94V-O Contact: Gold Plated Phosphor Bronze Alloy Insulation Resistance: 10M Ohm Minimum Contact Resistance: 20M Ohm Max. per contact Dielectric Withstand Voltage: 1000V AC RMS 60Hz Current Rating: 1.5 Amps Mechanical Life: 500 cycles minimum Retention Strength: 7.7kg between plug & socket

Specifications:

Housing: PBT Mixed 15% Glass Fibre, 94V-O Contact: Gold Plated Phosphor Bronze Alloy Insulation Resistance: 10M Ohm Minimum Contact Resistance: 20M Ohm Max. per contact Dielectric Withstand Voltage: 1000V AC RMS 60Hz Current Rating: 1.5 Amps Mechanical Life: 500 cycles minimum Retention Strength: 7.7kg between plug & socket

Specifications:

Housing: PBT Mixed 15% Glass Fibre, 94V-O Contact: Gold Plated Phosphor Bronze Alloy Insulation Resistance: 10M Ohm Minimum Contact Resistance: 20M Ohm Max. per contact Dielectric Withstand Voltage: 1000V AC RMS 60Hz Current Rating: 1.5 Amps Mechanical Life: 500 cycles minimum Retention Strength: 7.7kg between plug & socket

Specifications:

Housing: PBT Mixed 15% Glass Fibre, 94V-O Contact: Gold Plated Phosphor Bronze Alloy Insulation Resistance: 10M Ohm Minimum Contact Resistance: 20M Ohm Max. per contact Dielectric Withstand Voltage: 1000V AC RMS 60Hz Current Rating: 1.5 Amps Mechanical Life: 500 cycles minimum Retention Strength: 7.7kg between plug & socket

8 Way - 8 Wire RJ45. LED's for data applications.

Dimension Drawings

Specifications:

Housing: PBT Mixed 15% Glass Fibre, 94V-O Contact: Gold Plated Phosphor Bronze Alloy Insulation Resistance: 10M Ohm Minimum Contact Resistance: 20M Ohm Max. per contact Dielectric Withstand Voltage: 1000V AC RMS 60Hz Current Rating: 1.5 Amps Mechanical Life: 500 cycles minimum Retention Strength: 7.7kg between plug & socket

Specifications:

Housing: PBT Mixed 15% Glass Fibre, 94V-O Contact: Gold Plated Phosphor Bronze Alloy Insulation Resistance: 10M Ohm Minimum Contact Resistance: 20M Ohm Max. per contact Dielectric Withstand Voltage: 1000V AC RMS 60Hz Current Rating: 1.5 Amps Mechanical Life: 500 cycles minimum Retention Strength: 7.7kg between plug & socket

Specifications:

Housing: PBT Mixed 15% Glass Fibre, 94V-O Contact: Gold Plated Phosphor Bronze Alloy Insulation Resistance: 10M Ohm Minimum Contact Resistance: 20M Ohm Max. per contact Dielectric Withstand Voltage: 1000V AC RMS 60Hz Current Rating: 1.5 Amps Mechanical Life: 500 cycles minimum Retention Strength: 7.7kg between plug & socket

Specifications:

Housing: PBT Mixed 15% Glass Fibre, 94V-O Contact: Gold Plated Phosphor Bronze Alloy Insulation Resistance: 10M Ohm Minimum Contact Resistance: 20M Ohm Max. per contact Dielectric Withstand Voltage: 1000V AC RMS 60Hz Current Rating: 1.5 Amps Mechanical Life: 500 cycles minimum Retention Strength: 7.7kg between plug & socket

Specifications:

Housing: PBT Mixed 15% Glass Fibre, 94V-O Contact: Gold Plated Phosphor Bronze Alloy Insulation Resistance: 10M Ohm Minimum Contact Resistance: 20M Ohm Max. per contact Dielectric Withstand Voltage: 1000V AC RMS 60Hz Current Rating: 1.5 Amps Mechanical Life: 500 cycles minimum Retention Strength: 7.7kg between plug & socket

Specifications:

Housing: PBT Mixed 15% Glass Fibre, 94V-O Contact: Gold Plated Phosphor Bronze Alloy Insulation Resistance: 10M Ohm Minimum Contact Resistance: 20M Ohm Max. per contact Dielectric Withstand Voltage: 1000V AC RMS 60Hz Current Rating: 1.5 Amps Mechanical Life: 500 cycles minimum Retention Strength: 7.7kg between plug & socket

Specifications:

Housing: PBT Mixed 15% Glass Fibre, 94V-O Contact: Gold Plated Phosphor Bronze Alloy Insulation Resistance: 10M Ohm Minimum Contact Resistance: 20M Ohm Max. per contact Dielectric Withstand Voltage: 1000V AC RMS 60Hz Current Rating: 1.5 Amps Mechanical Life: 500 cycles minimum Retention Strength: 7.7kg between plug & socket

Specifications:

Housing: PBT Mixed 15% Glass Fibre, 94V-O Contact: Gold Plated Phosphor Bronze Alloy Insulation Resistance: 10M Ohm Minimum Contact Resistance: 20M Ohm Max. per contact Dielectric Withstand Voltage: 1000V AC RMS 60Hz Current Rating: 1.5 Amps Mechanical Life: 500 cycles minimum Retention Strength: 7.7kg between plug & socket

Specifications:

Housing: PBT Mixed 15% Glass Fibre, 94V-O Contact: Gold Plated Phosphor Bronze Alloy Insulation Resistance: 10M Ohm Minimum Contact Resistance: 20M Ohm Max. per contact Dielectric Withstand Voltage: 1000V AC RMS 60Hz Current Rating: 1.5 Amps Mechanical Life: 500 cycles minimum Retention Strength: 7.7kg between plug & socket

Contains 50 each of P 1412, P 1414, P 1415, P 1418.

8P8C Sheilded 8P8C Stranded

Cat5e RJ45 suit round cable

8P8C Sheilded 8P8C Solid

Cat5e RJ45 suit round cable

8P8C Solid/ Stranded

Cat5e RJ45 suit round cable

Suits stranded and solid conductors

Suits stranded and solid conductors

Suits stranded and solid conductors

Suits stranded and solid conductors

Suits P 5410 - P 5440 Pin Header plugs. Gold plated contacts. 2.54mm spacing.

Shunts with Tag Pack1000

Suits P 5410 - P 5440 Pin Header plugs. Gold plated contacts. 2.54mm spacing.

Shunts with Tag Pack100

Suits P 5410 - P 5440 Pin Header plugs. Gold plated contacts. 2.54mm spacing.

Shunts with Tag Pack10

Suits P 5410 - P 5440 Pin Header plugs. Gold plated contacts. 2.54mm spacing.

Standard Shunts Pack1000

Suits P 5410 - P 5440 Pin Header plugs. Gold plated contacts. 2.54mm spacing.

Standard Shunts Pack100

Suits P 5410 - P 5440 Pin Header plugs. Gold plated contacts. 2.54mm spacing.

Standard Shunts Pack10

5m

3m

1.5m

3m

1.5m

5m

3m

5m

3m

1.5m

5m

3m

1.5m

1.5m

5m

3m

3m

1.5m

1.5m

1 RCA Plug to 1 RCA Plug 3m

Dyna-Link interconnect leads
Standard series wth ultra soft outer sheath for easy installation

Dyna-Link interconnect leads
Standard series wth ultra soft outer sheath for easy installation

2.5mm Stereo Jack to 2.5mm Stereo Jack. 1.5 meters long, suits most walkmans, PC audio cards, and the like.

Dyna-Link interconnect leads
Standard series wth ultra soft outer sheath for easy installation

3m

1.5m

1.5m

Mono to Mono 5m

Stereo 5m

Stereo 3m

Stereo 1.5m

Stereo to Stereo 10m

Stereo to Stereo5m

Stereo to Stereo3m

Stereo to Stereo 1.5m (BULK Version - No Packaging)

Stereo to Stereo1.5m

Gold connectors, rubber strain relief, plus extra thick sheathing for reduced signal interference.

Toslink 1.5m

Diecast platnium finish connectors with 24ct gold contact surfaces. Ideal for use with iPod or video devices equipped with a 3.5mm jack ie camcorder, digital cameras etc.

1.5m

Diecast connector bodies, gold plated contacts.

24K gold connectors

Diecast connector bodies. Gold plated contact surfaces

1.5m

Diecast connector bodies, gold plated contacts.

0.75m

Toslink Female to 3.5mm Optical

Toslink Female to 3.5mm Optical

Female to Female Toslink joiner.

Female to Female Toslink joiner.

Fem-fem 2 way splitter

1.5m

High quality gold plated RCA connectors with flexable colour coded leads.
Suitable for RGB or component video signals.

High quality gold plated RCA connectors with flexable colour coded leads.
Suitable for RGB or component video signals.

High quality gold plated RCA connectors with flexable colour coded leads.
Suitable for RGB or component video signals.

High quality gold plated RCA connectors with flexable colour coded leads.
Suitable for RGB or component video signals.

Standard series wth ultra soft outer sheath for easy installation

Bulk part.

Dyna-Link interconnect leads
Standard series wth ultra soft outer sheath for easy installation

3.5mm Stereo plug - 3.5mm socket

1.5m

3.5mm Stereo plug - 3.5mm stereo plug

0.75m

This wallplate ADSL filter plugs into your existing telephone wallplate and provides a filtered connection for your telephone and an unfiltered output for your ADSL modem.

Line filters are required to use devices (such as telephones, faxes & answering machines) on the same phone line with an ADSL modem. .

Filter: RJ12 line and phone connections

3.5mm plug to RJ12 6P6C modular

Telecom plug 605A

60cm RJ10 to RCA Plug Lead

Length 1.8m

Telecom part no 605M.
Standard phone plug to 6 way, 2 wire modular socket 2m lead.

Telecom part no 606M.
Standard phone plug to 6 way, 4 wire modular socket 2m lead.

All 4 Conductor. Length 15m

All 4 Conductor. Length 10m

Modular lead, 10m length. 6P4C RJ12 to 6P4C RJ12.

6P4C-6P4C

6P4C-6P4C

6P4C-6P4C

6P4C-6P4C

8P4C-6P4C modular telephone connection lead. 

8P4C-6P4C

3m. BULK only - No packaging.

1.5m. BULK only - No packaging.

HDMI V1.3 Leads 1.5m

HDMI male to HDMI male. V1.3

HDMI certified. Lifetime warranty. Diecast platinum finish plugs with gold plated contacts. Woven outer sheath for the ultimate durability. Internal mylar foil shielding for improved performance even over 15m lengths.

• High Speed Category 2 HDMI 1.3 cable
• 10.2Gbit/s (340MHz) bandwidth
• Maximum resolution HD 1920 x 1080
• HDCP compliant
• 24AWG cable guage with fibre wrap shielding
• Supports 48 bit Deep Colour
• Supports Dolby® Digital & DTS®
• Supports Dolby® TrueHDTM & DTS®-HD Master Audio
• Diecast connector bodies
• Platinium finish with 24ct gold plated contact surfaces
• Woven fibre sheath for ultimate durability
• Flexible strain relief

15m

HDMI certified. Lifetime warranty. Diecast platinum finish plugs with gold plated contacts. Woven outer sheath for the ultimate durability. Internal mylar foil shielding for improved performance even over 15m lengths.

• High Speed Category 2 HDMI 1.3 cable
• 10.2Gbit/s (340MHz) bandwidth
• HD resolution 1920 x 1080
• HDCP compliant
• 24AWG cable guage with fibre wrap shielding
• Supports 48 bit Deep Colour
• Supports Dolby® Digital & DTS®
• Supports Dolby® TrueHDTM & DTS®-HD Master Audio
• Diecast connector bodies
• Platinium finish with 24ct gold plated contact surfaces
• Woven fibre sheath for ultimate durability
• Flexible strain relief

10m

HDMI certified. Lifetime warranty. Diecast platinum finish plugs with gold plated contacts. Woven outer sheath for the ultimate durability. Internal mylar foil shielding for improved performance even over 15m lengths.

• High Speed Category 2 HDMI 1.3 cable
• 10.2Gbit/s (340MHz) bandwidth
• HD resolution 1920 x 1080
• HDCP compliant
• 26AWG cable guage with fibre wrap shielding
• Supports 48 bit Deep Colour
• Supports Dolby® Digital & DTS®
• Supports Dolby® TrueHDTM & DTS®-HD Master Audio
• Diecast connector bodies
• Platinium finish with 24ct gold plated contact surfaces
• Woven fibre sheath for ultimate durability
• Flexible strain relief

7.5m

HDMI certified. Lifetime warranty. Diecast platinum finish plugs with gold plated contacts. Woven outer sheath for the ultimate durability. Internal mylar foil shielding for improved performance even over 15m lengths.

• High Speed Category 2 HDMI 1.3 cable
• 10.2Gbit/s (340MHz) bandwidth
• HD resolution 1920 x 1080
• HDCP compliant
• 28AWG cable guage with fibre wrap shielding
• Supports 48 bit Deep Colour
• Supports Dolby® Digital & DTS®
• Supports Dolby® TrueHDTM & DTS®-HD Master Audio
• Diecast connector bodies
• Platinium finish with 24ct gold plated contact surfaces
• Woven fibre sheath for ultimate durability
• Flexible strain relief

5m

HDMI certified. Lifetime warranty. Diecast platinum finish plugs with gold plated contacts. Woven outer sheath for the ultimate durability. Internal mylar foil shielding for improved performance even over 15m lengths.

• High Speed Category 2 HDMI 1.3 cable
• 10.2Gbit/s (340MHz) bandwidth
• HD resolution 1920 x 1080
• HDCP compliant
• 28AWG cable guage with fibre wrap shielding
• Supports 48 bit Deep Colour
• Supports Dolby® Digital & DTS®
• Supports Dolby® TrueHDTM & DTS®-HD Master Audio
• Diecast connector bodies
• Platinium finish with 24ct gold plated contact surfaces
• Woven fibre sheath for ultimate durability
• Flexible strain relief

3m

HDMI certified. Lifetime warranty. Diecast platinum finish plugs with gold plated contacts. Woven outer sheath for the ultimate durability. Internal mylar foil shielding for improved performance even over 15m lengths. • High Speed Category 2 HDMI 1.3 cable • 10.2Gbit/s (340MHz) bandwidth • HD resolution 1920 x 1080 • HDCP compliant • 30AWG cable guage with fibre wrap shielding • Supports 48 bit Deep Colour • Supports Dolby® Digital & DTS® • Supports Dolby® TrueHDTM & DTS®-HD Master Audio • Diecast connector bodies • Platinium finish with 24ct gold plated contact surfaces • Woven fibre sheath for ultimate durability • Flexible strain relief

1.5m

Altronics has combined with one of Asia's largest manufacturers to develop this slimline range of plugpacks. All new slimline design allows two plugpacks up to 500mA rating (except for M 9449) to be plugged in, side by side, into a standard double power point. All models include a LED "On" indicator. The multi-voltage models incorporate a voltage selector switch which is inaccessible once plugged into the power point. This feature reduces the possibility of accidental adjustment of the desired voltage setting.

Approval No.Q99505 Supplied with 2.1mm DC Jack

Specifications:

10VAC @ 1A For a full range of reversible tips to suit this plugpack click here

Remote control unit allows you to perform all the functions available on the front panel of the M 8155 and M 8158 inverters, including switching between 240V and battery power, charge activation etc.

Supplied with 10m modular lead.

These state of the art pure sine wave UPS/inverters utilise sophisticated circuitry that includes a battery charger, inverter, solar regulator and an automatic bypass switch which allows them to be utilised in a wide variety of power backup installations. They are designed to be permanently connected to 240V mains grid power, a solar array and suitably sized battery bank. Under normal mains conditions the load is direct fed, under mains failure the inverter, powered from the battery bank, takes over and supplies the load. Switch over from mains to inverter is via the automatic bypass switch which switches within 8ms ensuring a seamless changeover. The control panel with LCD provides adjustments for mains output voltage, output frequency. Essential battery parameters can be monitored including capacity remaining, current and voltage. The control panel may be removed and located remotely via Cat5 UTP cable up to 50m from the main unit. Inverter: Produces a clean and smooth sine wave AC output with very low distortion (<3%) and precise frequency control. The soft-start circuitry and large surge capacity enable the units to power heavy inductive loads. The overload and short circuit protection system ensures safe and reliable operation. An internal bypass switch enables the unit to operate as an automatic backup power supply whilst connected to the mains grid. When connected to mains power the unit functions as a battery charger, keeping the backup cells topped up. If mains power fails, the unit automatically switches to inverter mode and continues to power the connected devices. No user intervention is required and the bypass switch will activate within 8ms, ensuring minimal power disruption. Battery Charger: Charges and maintains either gel cells or lead-acid battery banks up to 500Ah. The microprocessor circuitry ensures batteries are charged to their optimum capacity using a 3 step process. This maximises battery capacity and life. Charging parameters are user-configurable depending on battery size. This allows the charger to be matched precisely to the kinds of batteries being employed. Solar Regulator: The internal solar regulator allows direct connection of solar panels, integrating them into a remote power system. The connected batteries are charged and maintained automatically from the solar panels. If the unit is connected to mains power or a generator, battery charge is automatically balanced between mains and solar panels.

Features:

• Pure sine wave output with low distortion • Auto-switching between 240V mains and inverter output when mains fails • Suitable for fixed installations eg: backup power systems • Suitable for use in generator systems • Internal solar regulator • Built-in 5 stage battery charger • User programmable charge parameters for optimum battery charging • Gel cell or lead-acid battery compatible • Front panel can be remote mounted

Specifications:

Capacity 3.6KVA Surge rating 3500W (3-5 cycles) Output wave form Pure sine wave Battery input voltage 24V DC Efficiency at full load 80% Max charging current >50A No load current (inverter mode) 3.3A Minimum start load (inverter mode) 0% Output voltage 220-240V AC @ 50Hz Max output voltage 275V AC @ 50Hz Power factor 0.8 Frequency regulation ±0.1Hz Voltage regulation <3% RMS Low battery alarm Yes Low battery shutdown Yes Alarm & thermal shutdown Yes Short circuit protection Yes Operation temperature 0-40°C Weight 32kg Dimensions (mm) ≈450 x 300 x 190

These state of the art pure sine wave UPS/inverters utilise sophisticated circuitry that includes a battery charger, inverter, solar regulator and an automatic bypass switch which allows them to be utilised in a wide variety of power backup installations. They are designed to be permanently connected to 240V mains grid power, a solar array and suitably sized battery bank. Under normal mains conditions the load is direct fed, under mains failure the inverter, powered from the battery bank, takes over and supplies the load. Switch over from mains to inverter is via the automatic bypass switch which switches within 8ms ensuring a seamless changeover. The control panel with LCD provides adjustments for mains output voltage, output frequency. Essential battery parameters can be monitored including capacity remaining, current and voltage. The control panel may be removed and located remotely via Cat5 UTP cable up to 50m from the main unit. Inverter: Produces a clean and smooth sine wave AC output with very low distortion (<3%) and precise frequency control. The soft-start circuitry and large surge capacity enable the units to power heavy inductive loads. The overload and short circuit protection system ensures safe and reliable operation. An internal bypass switch enables the unit to operate as an automatic backup power supply whilst connected to the mains grid. When connected to mains power the unit functions as a battery charger, keeping the backup cells topped up. If mains power fails, the unit automatically switches to inverter mode and continues to power the connected devices. No user intervention is required and the bypass switch will activate within 8ms, ensuring minimal power disruption. Battery Charger: Charges and maintains either gel cells or lead-acid battery banks up to 500Ah. The microprocessor circuitry ensures batteries are charged to their optimum capacity using a 3 step process. This maximises battery capacity and life. Charging parameters are user-configurable depending on battery size. This allows the charger to be matched precisely to the kinds of batteries being employed. Solar Regulator: The internal solar regulator allows direct connection of solar panels, integrating them into a remote power system. The connected batteries are charged and maintained automatically from the solar panels. If the unit is connected to mains power or a generator, battery charge is automatically balanced between mains and solar panels.

Features:

• Pure sine wave output with low distortion • Auto-switching between 240V mains and inverter output when mains fails • Suitable for fixed installations eg: backup power systems • Suitable for use in generator systems • Internal solar regulator • Built-in 5 stage battery charger • User programmable charge parameters for optimum battery charging • Gel cell or lead-acid battery compatible • Front panel can be remote mounted

Specifications:

Capacity 2.4KVA Surge rating 3220W (3-5 cycles) Output wave form Pure sine wave Battery input voltage 24V DC Efficiency at full load 80% No load current consumption (inverter mode): 2.8A Minimum start load (inverter mode): 0% Max charging current >50A Output voltage 220-240V AC @ 50Hz Max output voltage 275V AC @ 50Hz Power factor 0.8 Frequency regulation ±0.1Hz Voltage regulation <3% RMS Low battery alarm Yes Low battery shutdown Yes Alarm & thermal shutdown Yes Short circuit protection Yes Operation temperature 0-40°C Weight 24kg Dimensions (mm) ≈450 x 300 x 190

Remotely monitor and operate your inverter from inside your home, boat, caravan or 4WD with this unit. Once installed, it overrides the controls on the inverter. The unit can be mounted up to 50m (10m lead supplied) from the inverter and simply plugs into the inverter via a standard modular socket. Suits the M 8153, M 8042 and M 8146 inverters.

Temperature sensor to suit the M 8155 and M 8158 inverters. Simply reads the external temperature of your batteries allowing the inverter to regulate power as required.

Industry standard pinout. Wide operating voltage range. Low ripple & noise. Auto short circuit protection. Low operating temperature.

9-36VDC to 12VDC


Dimension Drawings

Input voltage DC 9-36V
Output voltage DC 12V
Output current 250mA
Output regulation ±0.2%
Ripple & noise 100mV p-p
I/O isolation voltage 1000V DC
I/O resistance >1GΩ
Isolation capacitance <80pF
Efficiency >70%
Operating temperature -25 to 70°C

Industry standard pinout. Wide operating voltage range. Low ripple & noise. Auto short circuit protection. Low operating temperature.

9-36VDC to 5VDC

Dimension Drawings

Input voltage DC 9-36V
Output voltage DC 5V
Output current 600mA
Output regulation ±0.2%
Ripple & noise <100mV p-p
I/O isolation voltage 1000V DC
I/O resistance >1GΩ
Isolation capacitance <80pF
Efficiency >70%
Operating temperature -25 to 70°C

Industry standard pinout. Wide operating voltage range. Low ripple & noise. Auto short circuit protection. Low operating temperature.

10.8-13.2VDC to 5VDC

Input voltage DC 10.8-13.2V
Output voltage DC 5V
Output current 200mA
Output regulation ±0.5%
Ripple & noise <100mV p-p
I/O isolation voltage 1000V DC
I/O resistance >1GΩ
Isolation capacitance <80pF
Efficiency >50%
Operating temperature -25 to 70°C

Dimension Drawings

Manufactured using very high quality grain oriented silicon steel. This results in a compact, high performance, high output transformer.

Specifications:

Primary Voltage: 240V AC Total VA Rating: 10VA Insulation: Class A (105°C) Magnetising Current: <30mA Temperature Rise: <65°C Regulation: 11% Weight: 250g PCB Hole Size: 1.2mm Secondary Voltage: 11 + 14

Note: Must be used with a standard 100mA external fuse.

Perfect for powering a huge range of 12V automotive appliances from a 24V battery bank. This device converts 24VDC to 13.8V DC at a massive 20 amps! Suitable for use with stereos, CB radios, lighting etc in trucks, buses, cars or boats. 24V input wiring connects via screw terminals, 13.8V output connects via binding posts.

Features:

• Overload protection • Over-current protection • Rated at 20 amps continuous, 25 amps peak • On / Off power switch • Fused • Extremely compact and rugged • Quality construction • High efficiency

Specifications:

Output Voltage: 13.8V DC Current rating: 20A Line Regulation: <20mV Efficiency: >89% Ripple: <20mV p-p Dimensions: 210 x 55 x 160mm (L x H x W)

Converts 24V DC to 13.8V DC for use with stereos, CB radios, two ways etc. Suitable for vehicles fitted with 24V electrical systems, eg. trucks, boats, tractors etc.

Features

• Overload protection • Over-current protection • Rated at 8 amps continuous, 10 amps peak • On / Off power switch • Fused • Extremely compact and rugged • Quality construction • Efficiency > 88%

Specifications

Output Voltage: 13.8V DC Current rating: 8A Line Regulation: <15mV Efficiency: >88% Ripple: <12mV p-p Dimensions: 140 x 50 x 125mm (L x H x W)

A multi-voltage plug pack with the adjustment switch on the side of the unit that faces the wall when installed. This prevents accidental change of output voltage which may cause damage to a connected appliance. In addition, the adjustment has to be made with the included “key” or flat blade screwdriver.

Approval No. Q99505 3V - 12V/1.2A Supplied with 6 Adaptors

Specifications:

3, 4.5, 6, 7.5, 9, 12V @ 1.2A Max

A slim line multi-voltage plug pack with the adjustment switch on the side of the unit that faces the wall when installed. This prevents accidental change of output voltage which may cause damage to a connected appliance. In addition, the adjustment has to be made with the included “key” or flat blade screwdriver.

Approval No. Q99505 3V/1.6A - 12V/0.8A Supplied with 6 Adaptors

Specifications:

800mA @ 12V 1A @ 9V, 1.2A @ 7.5V 1.5A @ 6V 1.6A @ 3V, 4.5V

1000W, Converts 240V to 120V for powering US appliances on Australian mains. Fitted with US mains socket.
Secondary Rating: 120V 8.4A

Please note: Before connecting equipment please check the wattage rating of your your appliance against this transformer. Overloading the transformer will cause damage to the transformer which is not covered under warranty. If you're not sure if this transformer will be suitable for your appliance, please contact us prior to purchasing. 

M8187 500W, converts US applications to Australian main voltages.

M8185 250W, converts US applications to Australian main voltages.

M8183 120W, converts US applications to Australian main voltages.

M8180 50VA, converts US applications to Australian main voltages.

Primary fitted with 200mm fly leads. Secondary taps have solder tags.

Specificatons:

Primary voltage: 240V AC Total VA rating: 60VA Insulation: Class E (120°C) Magnetising current: <80mA Temperature rise: <65°C Regulation: ˜10% Recommended primary AC fuse: 500mA Weight: ˜1.4kg Primary connection: 200mm fly leads Secondary connection: Solder tags AS/NZS 61558.2.6 approval: Q042028 AS3108 approval: CS/813/Q

PDF Download:

Dimension Drawings

Note: Must be used with a standard 500mA external fuse.

Primary fitted with 200mm fly leads. Secondary taps have solder tags.

Specifications

Primary voltage: 240V AC Total VA rating: 30VA Insulation: Class E (120°C) Magnetising current: <80mA Temperature rise: <65°C Regulation: ˜8% Recommended primary AC fuse: 500mA Weight: ˜1kg Primary connection: 200mm fly leads Secondary connection: Solder tags AS/NZS 61558.2.6 approval: Q042029 AS3108 approval: CS/814/Q

PDF Download:

Dimension Drawings

Note: Must be used with a standard 500mA external fuse.

Connection: Flying Lead
Air Flow: 77CFM
Input Power: 18W
Speed: 2000 - 2200 RPM
Noise Level: 45dBA
Material: Diecast Alum. Frame
Size: 120 x 120 x 25mm
Bearing Type: Sleeve Bearing
Blade Type: Plastic

Connection: Terminals
Air Flow: 105CFM
Input Power: 20W
Speed: 2550 - 2900 RPM
Noise Level: 43dBA
Material: Diecast Alum. Frame
Size: 120 x 120 x 38mm
Bearing Type: Sleeve Bearing
Blade Type: Plastic

Connection: Flying Lead
Air Flow: 30CFM
Input Power: 14W
Speed: 2300 - 2750 RPM
Noise Level: 31dBA
Material: Diecast Alum. Frame
Size: 80 x 80 x 38mm
Bearing Type: Sleeve Bearing
Blade Type: Plastic

Connection: Flying Lead
Air Flow: 36CFM
Input Power: 2.9W
Speed: 3000 RPM
Noise Level: 34dBA
Material: Thermoplastic
Size: 80 x 80 x 25mm
Bearing Type: Sleeve Bearing
Blade Type: Plastic

Quality 80mm Sunon brand cooling fan. Suitable replacement for computer case and power supplies. Flying lead connections.

Specifications

Connection: Flying Lead Air Flow: 31CFM Speed: 2300 RPM Noise Level: 26dBA Material: Thermoplastic Size: 80 x 80 x 25mm Bearing Type: Sleeve Bearing

Connection: Flying Lead
Air Flow: 21.7CFM
Input Power: 2.6W
Speed: 4500 RPM
Noise Level: 34dBA
Material: Thermoplastic
Size: 60 x 60 x 25mm
Bearing Type: Sleeve Bearing
Blade Type: Plastic

Connection: Flying Lead
Air Flow: 20CFM
Input Power: 1.6W
Speed: 3800 RPM
Noise Level: 27dBA
Material: Thermoplastic
Size: 60 x 60 x 25mm
Bearing Type: Sleeve Bearing
Blade Type: Plastic

General purpose cooling fan with feedback for speed control.Whisper quiet 26dB operation and low current draw 90mA at full capacity 31-33CFM. Features maglev construction.
Dimensions: 80Wx80Lx25.4H

 

Specifications:

Connection Type: 3 Wire Voltage: 12VDC Operating Voltage: 5-13.8VDC Rated Speed: 2300 RPM Air Flow: 31 CFM Rated Current: 0.09A Rated Power: 1.1W Noise Level: 26dB Operating Temperature: -10 to +70 deg C. Bearing System: Maglev

Premium quality Sunnon fan with "Maglev" bearing.
Ideal for replacing worn video card fans.

Specifications

Connection: Flying Lead Air Flow: 8CFM Input Power: 1W Speed: 7000 RPM Noise Level: 32dBA Material: Thermoplastic Size: 40 x 40 x 10mm Bearing Type: Maglev

Suits all 120mm AC models. Moulded plug to bare ends. Simply plugs onto the terminals on the fan. Length 1m

Allows fixing of 25mm slimline fans and fan guards without the need for bolts.

Max panel thickness 1.5mm.
Mounting hole 4mmØ.

Allows fixing of 25mm slimline fans and fan guards without the need for bolts.

Max panel thickness 1.5mm.
Mounting hole 4mmØ.

Allows fixing of 25mm slimline fans and fan guards without the need for bolts.

Max panel thickness 1.5mm.
Mounting hole 4mmØ.

40mm robust metal guard designed to prevent accidental contact with rotating fan blades. Simply fixes to the chassis via the fan mounts.

80mm robust metal guard designed to prevent accidental contact with rotating fan blades. Simply fixes to the chassis via the fan mounts.

80mm plastic fan guard with grille.

Robust metal grill designed to prevent accidental contact with rotating fan blades. Simply fixes to the chassis via the fan mounting bolts.

80mm

Robust metal grill designed to prevent accidental contact with rotating fan blades. Simply fixes to the chassis via the fan mounting bolts.

120mm

Suits all 120mm models. Ideal for equipment requiring fan cooling installed in dusty environments. Simple foam filter prevents dust particles from entering the equipment. We recommend periodic cleaning to prevent the filter from clogging and the restricting airflow.

120mm

Robust metal grill designed to prevent accidental contact with rotating fan blades. Simply fixes to the chassis via the fan mounting bolts.

60mm

60mm robust plastic guard designed to prevent accidental contact with rotating fan blades. Simply fixes to the chassis via the fan mounts.

(SC June ‘09) Provides an adjustable 10Hz to 30kHz output in sine, square, triangle and sawtooth waveforms for testing amplifiers, speakers and other audio devices. Three output ranges: 20mV, 200mV & 1V. Requires 9V battery.